Masonry & Brickwork
Net Wall Area Calculator
Net wall area for paint, board, render and masonry: gross wall less the doors and windows, in m² and ft²
Updated October 9, 2026 · Live
What this tool does
Works out the net area of a wall by taking the door and window openings off the gross length-times-height face, in square metres or square feet. It shows the gross, each kind of opening, the openings' share and the net in both units, and explains when estimating conventions leave small openings in.
Length times height, less each door and window times its count; the net in both units with the openings' share.
People also use
Formula Used
Formula Used
How the net wall area calculator works
Every wall take-off starts with the same subtraction: the whole face of the wall, less the holes in it. Length times height is the gross; each door is its width times its height times how many there are, each window the same; take both away and what is left is the net area that gets painted, boarded, rendered or bricked. The Brick Industry Association's Technical Note 10 on dimensioning and estimating brick masonry calls this the wall-area method and says it is the most widely used estimating procedure because of its simplicity: "multiplying the net wall area (gross areas less areas of openings) by known quantities of material required per square foot (square meter)". This calculator is that first multiplication, with the openings' share of the wall shown so you can see how much of the elevation is glass and door.
The US default is a 16 ft by 8 ft wall with one 3 ft by 6 ft 8 in door and one 4 ft by 4 ft window: 128 ft² gross, 20 ft² of door, 16 ft² of window, 92 ft² net (8.55 m²), with the openings taking 28% of the face. The metric default, 5 m by 2.4 m with a 0.9 m by 2.0 m door and a 1.2 m square window, is 12.00 m² gross, 1.80 m² of door and 1.44 m² of window, 8.76 m² net (94.3 ft²), 27% openings. The calculator assumes all the doors on the wall are one size and all the windows another; for a wall with a patio door and two casements, run it once per opening size and add the deductions by hand, or treat the odd one as a window of its own size.
When not to deduct an opening
The calculator deducts every opening you give it, and that is right for ordering brick, blocks, boards and tiles, where a hole is a hole. Measurement conventions for pricing labour are not always so literal. The RICS New Rules of Measurement, NRM 2 rule for masonry walls is that "no deductions should be made for voids or built-in items with a cross-sectional area equal to or less than 0.50 m²", so a quantity surveyor measuring a UK brick wall to those rules would leave a small window in the wall area and deal with the opening itself as a separate item. The American painting trade goes further: the Painting Contractors Association's standard P10 on measuring surface area for painting says a small opening that interrupts a continuous surface is "disregarded and considered part of the continuous surface", that floor-to-ceiling openings over five feet wide are deducted, and that "all openings 100 square feet or larger are deducted". The practical reason is that cutting in around a window costs about as much labour as rolling the wall it sits in. So if you are costing a painter's time to those conventions, set the window count to zero for anything under 100 ft² (9.3 m²) and keep the deduction for the patio door; if you are buying the paint, deduct everything and let the tin rounding carry the trims and reveals.
Measuring the wall
Length is the run of the wall along the floor or the ground, height is floor to ceiling inside or ground to eaves outside, and for a gable the triangle above the eaves is half its base times its rise, added as a second run with no openings. Measure doors and windows to the structural opening for masonry, which is the hole in the wall, and to the frame or architrave for paint and board, which is the edge you cut to; the difference on a standard door is around a sixth of a square metre and does not usually change a bag or a roll, but on a wall of windows it adds up. Inside, measure each room's walls as one run around the perimeter at the ceiling height and enter the whole room's doors and windows together; outside, each elevation on its own, because the openings and the finish differ wall by wall.
Three walls worked
A 40 ft by 9 ft garage side wall with two 3 ft by 6 ft 8 in doors and four 3 ft by 5 ft windows: 360 ft² gross, 40 ft² of doors, 60 ft² of windows, 260 ft² net and 28% openings. A 12 m by 2.7 m internal run with two 0.9 m by 2.1 m doors and three 1.5 m by 1.2 m windows: 32.40 m² gross, 3.78 m² of doors, 5.40 m² of windows, 23.22 m² net. And a 4 m by 2.4 m rear wall that is mostly a 2.4 m by 2.1 m patio door: 9.60 m² gross less 5.04 m² of door is 4.56 m² of wall, 52% openings, which is the case where deducting matters most and where a painter would deduct too.
What the net area is for
The net area is the quantity that feeds every finish calculator on this site. For paint it is the area divided by the tin's coverage, for plasterboard the area divided by a board, for render and plaster the area times the thickness, for brick and block the area times the units per square metre or per 100 ft² from the maker's table, and the brick calculator, block calculator, drywall calculator and paint calculator each take it from here. None of the finish quantities carry a waste allowance until those calculators add one, and the net area itself has none: it is a measurement, not an order.
What the calculator leaves out
It does not handle a sloping top, an arch or a curved wall except by averaging the height, and it does not know about reveals, the strips of wall inside a window opening that are painted and plastered but not bricked; for a deep reveal add its perimeter times its depth to the paint area by hand. It does not price anything or allow waste. And it cannot tell which convention your estimator or your builder is pricing to; that paragraph on when not to deduct is the most it can do.
Using this with other BuildMetricLab tools
Take the net area to the repointing mortar calculator for an existing wall, the stucco calculator or exterior paint calculator for a finished one, and the wallpaper calculator inside. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.
Sources & methodology
Net wall area = length × height − (doors × door width × door height) − (windows × window width × window height), all doors one size and all windows one size; openings share = openings ÷ gross. US inputs are converted to metres before the sum and shown in ft² and m². Every opening entered is deducted; measurement conventions that ignore small openings (RICS NRM 2 masonry: voids ≤ 0.50 m² not deducted; PCA P10 painting: small openings disregarded, openings ≥ 100 ft² or floor-to-ceiling and over 5 ft wide deducted) are for the reader to apply. The wall-area method itself is as described in BIA Technical Note 10.
- Brick Industry Association, Technical Note 10, Dimensioning and Estimating Brick Masonry (2009): the wall-area method, net wall area = gross less openings, brick and mortar per 100 ft² and per 10 m²
- RICS, NRM 2: Detailed measurement for building works, 2nd edition (2021), masonry: no deduction for voids or built-in items with a cross-sectional area of 0.50 m² or less
- Painting Contractors Association, PCA P10 Measurement of Surface Area for Estimating Painting and Decorating Work, section 5.8: small openings disregarded; floor-to-ceiling openings over 5 ft wide and all openings of 100 ft² or more deducted
Frequently asked questions
Are net wall area calculator results accurate enough to order materials?
The subtraction is exact, so the net area is as accurate as the measurements you enter. It carries no waste allowance; the brick, board, paint and render calculators add their own on top. Measure openings to the structural opening for masonry and to the frame for finishes, and remember that measurement conventions such as RICS NRM 2 and the PCA P10 standard leave small openings in the measured area when work is measured for pricing.
Does this calculator include an allowance for wastage or cut-offs?
No. This tool computes the net wall area only: gross wall area minus the door and window openings you enter. It adds no wastage percentage, because the right allowance depends on the material; the brick, block, drywall and paint calculators each apply their own to this figure. If you are ordering by hand, add the trade allowance for that material on top of the net area.
Does this replace professional advice?
No. It is a measurement, not a design or a specification. Which openings to deduct, what reveals and returns to add, and whether a wall needs lintels, ties or a damp-proof course are matters for the measurement convention and the building code you work to. For anything affecting structure, gas, electrics, plumbing or drainage to a public sewer, use a suitably qualified professional.
Can I change the unit prices?
There are no prices on this page; it returns an area. Take the net area to the material calculator for your finish, where the unit prices are yours to enter, or multiply it by a supplier's rate per m² or per ft² yourself.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













