Wall & Ceiling
Wallpaper Calculator
Estimate the wallpaper rolls for a room from wall area, roll size and pattern wastage
Updated May 13, 2026 · Live
What this tool does
Estimates the wallpaper rolls needed for a room from the wall area, the area one roll covers and a pattern wastage allowance.
Enter the wall area, the area one roll covers and a wastage allowance; the calculator returns the rolls to buy and an estimated cost.
People also use
Formula Used
Formula Used
How the wallpaper calculator works
The calculator estimates rolls from area. It adds a pattern wastage allowance to the wall area, divides by the area one roll covers, and rounds up to a whole roll:
Rolls = ceil( wall area × (1 + wastage ÷ 100) ÷ coverage per roll )
The default entry is 400 ft² (37 m²) of wall, 56 ft² (5.2 m²) double rolls and 15% wastage. The area with wastage is 400 × 1.15 = 460 ft², and 460 ÷ 56 = 8.21, so you need 9 rolls. Nine rolls cover 504 ft², and at $28 a roll the estimate is $252. An exact fit is not rounded up. Wall area is the perimeter times the height, less large openings, so a 13 × 13 ft room with 8 ft walls is 52 × 8 = 416 ft² (38.6 m²).
Decorators usually count drops instead. A drop is one strip cut to the wall height plus the pattern repeat and a little trim. Rolls = ceil( drops needed ÷ drops per roll ), where drops needed = room perimeter ÷ roll width and drops per roll = whole number of drop lengths that fit in the roll.
Take a 13 × 13 ft room (4 × 4 m) with 8 ft (2.4 m) walls and a double roll of 20.5 in × 33 ft (0.52 × 10.05 m). The perimeter is 52 ft, and 52 ÷ 1.708 ft wide = 30.4, so you need 31 drops. With an 18 in (0.46 m) repeat a drop is 9.5 ft, and 33 ÷ 9.5 = 3.5, so only 3 drops fit in a roll. That is 31 ÷ 3 = 10.3, so 11 rolls. The tool's area estimate for the same room (416 ft², 15%, 56 ft² rolls) is 8.54, which is 9 rolls. Even a plain paper needs 3 drops per roll here (8.5 ft each, 25.5 ft of 33 ft), so 11 rolls again. Count the drops whenever the walls are tall for the roll or the repeat is large.
Typical US wall and ceiling wastage
The default wastage is 15%. It covers trimming at the ceiling and baseboard, the offcuts left when strips are cut to height, and matching the pattern from one strip to the next. A straight match lines the pattern up at the same height across the wall. A half-drop match offsets alternate strips, so the offcut from one strip rarely fits the next. Large repeats waste more, and plain or random-match papers waste less. These are common working allowances and not figures from a standard.
The field accepts up to 40%. Because the real waste comes from the roll length and the repeat, not from a percentage of area, treat the result as a first estimate and check it by counting drops.
What this tool does not do
It does not subtract individual door and window openings, count drops per roll for your pattern repeat, or choose the paste. It does not replace a professional quote or adjust for local prices. The roll width, length and pattern repeat printed on the label are what you need for a drop-by-drop count. Those decisions remain with the manufacturer's instructions and a qualified decorator.
On-site considerations for wallpaper
Prepare the wall first. Fill and sand it, clean off grease and dust, and seal bare plaster or fresh drywall as the paper maker directs. Old wallpaper often has to come off first, and steam or scoring makes this easier. Paper hung over damp, flaking or unsealed walls tends to bubble and lift.
Check what is under old layers before you scrape or sand. In the United States, homes built before 1978 may have lead-based paint, and the EPA's Renovation, Repair and Painting program sets lead-safe rules for contractors working in them. Older textured coatings and plasters can contain asbestos in some countries, so have suspect material tested before you disturb it.
Codes and compliance
There is no building code for hanging wallpaper, but some rules touch the work. Wallcoverings in commercial buildings and some multi-family corridors can be subject to flame-spread and smoke ratings, which depend on the local fire code. In older homes, lead-safe work practices apply to disturbing painted surfaces (EPA, United States). Ask your local building department or the paper's data sheet if the room is not a typical dwelling. Outside the US, check the rules of your own country; they differ.
Before you order
Buy all the rolls for the room at the same time and check that every roll has the same batch (run) number, because shade can differ between print runs. Unwrap the rolls and lay them out before hanging to check for faults. Partial or opened rolls are often not returnable. US wallpaper is commonly sold as a double roll of about 56 ft², but some papers are sold as single rolls of about 28 ft², so use the coverage on the label for the product you buy. Keep a spare roll for repairs.
Adjusting the defaults
Every input is editable: wall area, coverage per roll, pattern wastage and price per roll. Measure the perimeter of the room, multiply by the height, and subtract large openings. Enter the roll coverage printed on the label. The pre-filled figures only give the page a first result, so replace all of them with your own. Use the unit switch at the top of the page to enter square feet or square metres. A blank price leaves the cost out, and a blank or zero wall area or roll coverage is refused.
Using this wallpaper calculator alongside other BuildMetricLab tools
Use the roll count with the paint, primer and wallpaper paste calculators to plan the whole decorating job. The results can also be sent to the PlainEstimate hand-off to be priced. All BuildMetricLab tools run entirely in your browser, with no sign-up and nothing sent to a server, and every formula is shown on the page so you can check the maths.
Sources & methodology
Rolls = ceil( wall area × (1 + wastage) ÷ coverage per roll ). Area is in ft²; the ceiling function rounds up to a whole roll and an exact fit is not rounded up. Cost = rolls × price per roll. This is an area estimate. The drop method (drops needed = perimeter ÷ roll width; drops per roll = whole drops of height + repeat in the roll length) is shown in the text as a cross-check. A blank price drops the cost row; a blank, zero or negative area, coverage or wastage is refused.
Frequently asked questions
Are wallpaper calculator results accurate enough to order materials?
The roll count is exact arithmetic for the area and wastage you enter, but wallpaper is cut in strips, so the true count depends on the wall height, the roll length and the pattern repeat. Use the result as a first estimate and check it by counting drops before you order.
What wastage percentage should I use?
The default is 15%, a common allowance that covers trimming and pattern matching. Plain and random-match papers waste less, and large repeats or tall walls can need much more. It is a rule of thumb, not a standard figure, and the field accepts up to 40%.
Is this a substitute for professional advice?
No. This tool is a planning estimator only. For work that affects structure, building code compliance, electrical work, or lead or asbestos in older surfaces, consult a licensed contractor or design professional.
Can I change the unit prices?
Yes. Every price field is editable. Enter the price per roll from your supplier's quote, and make sure the coverage matches the roll size that price is for, because single and double rolls differ.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













