BuildMetricLab

Roofing

Roofing Underlayment Calculator

Estimates synthetic underlayment, felt, or ice and water shield rolls needed

Updated May 13, 2026 · Live

What this tool does

Estimates synthetic underlayment, felt, or ice and water shield rolls needed.

Calculates how many underlayment rolls a roof requires based on area, roll coverage, and lap overlap.

Inputs
ft²
ft²
%
$
Result

Roofing Felt Rolls Required

12

Roof Area
2,000.0 ft² (185.8 m²)
With 15.0% Overlap
2,300.0 ft² (213.7 m²)
One Roll Covers
200.0 ft² (18.6 m²)
Rolls Needed (exact)
11.50
Spare After Rounding
100.0 ft² (9.3 m²)
Estimated Cost
$456.00

Diagram

2000 ft²
Price it on PlainEstimate

Opens these materials as a new estimate on PlainEstimate, our free estimate and invoice app.

Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
N=⌈A⋅(1+o)C⌉N = \left\lceil \frac{A \cdot (1 + o)}{C} \right\rceil
NN
Roofing felt rolls required
AA
Roof area
oo
Overlap allowance (decimal)
CC
Roll coverage area

How the roofing underlayment calculator works

The tool turns a roof area and a roll size into a whole number of rolls. The formula is rolls = ceil(roof area × (1 + overlap ÷ 100) ÷ area of one roll). With the defaults, a 2,000 ft² roof (185.8 m², or 20 roofing squares) becomes 2,000 × 1.15 = 2,300 ft². One roll covers 200 ft² (18.6 m²), so 2,300 ÷ 200 = 11.5, which rounds up to 12 rolls. At $38 a roll that is $456.00, and the 12 rolls leave 100 ft² (9.3 m²) spare. The tool shows the exact figure (11.50) and the spare so you can see how close a roll count is to the next whole roll.

Enter the sloped area, not the footprint. A footprint of 1,600 ft² (148.6 m²) under a 6:12 roof (26.6°) is 1,600 × 1.118 = 1,789 ft² of roof. The roof area calculator and roof pitch calculator do that conversion.

Typical US roofing wastage

Underlayment has no wastage input here. The single Overlap figure covers laps and cut-offs together. For a 36 in (0.91 m) wide felt roll with a 2 in (50 mm) side lap, each course uses 34 of the 36 inches, so the roof needs 36 ÷ 34 = 1.059 times the area. Add a 4 in (100 mm) end lap on a 144 ft (43.9 m) roll and the factor becomes about 1.09. The remaining 6% of the 15% default allows for hips, valleys, vents and the first course along the eave. Complex roofs with many penetrations can justify 20%.

The double-coverage layout used on low slopes (commonly 2:12 up to 4:12) laps each sheet about 19 in (480 mm) over a 36 in sheet, so each course adds only 17 in (430 mm). The factor is then 36 ÷ 17 = 2.12, which means an overlap of about 112%. The input accepts up to 120% for this case. Check the layout your code edition and the manufacturer require.

What this tool does not do

It does not decide which product you need (felt, synthetic or self-adhering ice barrier), check that the product is approved for your roof covering and slope, or work out nailing and fastener counts. Each product is a separate calculation: run ice barrier on its own, using eave length × strip width as the area, then run the field underlayment for the rest. It does not add the cost of accessories, cap nails, tape or labour, and it does not check structure, ventilation or code compliance.

On-site considerations for roofing underlayment

Roof work is work at height. In the United States, OSHA 1926.501 requires fall protection from 6 ft (1.8 m) in construction. On roofs steeper than 4:12 that means guardrails with toeboards, safety nets or a personal fall arrest system. Other countries set their own rules; in Great Britain it is the Work at Height Regulations 2005, with guidance from the HSE. Felt and wet synthetic sheet are slippery. Lay underlayment in dry weather, fasten it as you go, and do not leave a loose roll on the slope. Pre-2000 roofs elsewhere may hold asbestos, so test an old covering before it is disturbed.

Codes and compliance

Roof coverings and underlayment in most US jurisdictions follow the International Residential Code, Chapter 9 (ICC), as adopted and amended by your state or city. For asphalt shingles it sets the underlayment type, the laps and a self-adhering ice barrier where ice has formed along the eaves in the past. Felt is made to ASTM D226 and self-adhering sheet to ASTM D1970. Lap dimensions and edition numbers change, so read the section your building department has adopted. Outside the US, use your own standard, such as BS 5534 in the UK or AS/NZS 4200 in Australia and New Zealand.

Before you order

Check the label for the roll width and length, then multiply for the gross area. A 3 ft × 144 ft roll is 432 ft² (40.1 m²). Buy the lap that the manufacturer states, because that sets the overlap you enter. Order a full extra roll when the exact figure ends close to a whole number, such as 11.9, since one cut-off in the wrong place uses more than the plan suggests. Ask the supplier whether the quoted roll is the gross size or a net coverage after laps, and keep the product on the same lot as the rest of the roof.

Adjusting the defaults

Every input can be changed. If you are using a product whose label already shows net coverage after laps, enter that figure for the roll and set the overlap to 0 for the laps, adding only a few per cent for cut-offs. Price per roll is optional: leave it blank and the cost line disappears. The default price of $38 is a placeholder, not a market figure.

Using this roofing underlayment calculator alongside other BuildMetricLab tools

A typical estimate runs roof area, then underlayment, then shingles or tiles. Use the roof area calculator for the sloped area, the shingle calculator for the covering, and the roof flashing calculator and roof ventilation calculator for the details. Everything runs in your browser, nothing is sent anywhere, and the formula is shown so you can check the maths.

Sources & methodology

Rolls = ceil(roof area × (1 + overlap ÷ 100) ÷ area of one roll). Roof area and roll area are entered in the unit shown and converted exactly (1 ft² = 0.09290304 m²). The overlap is one allowance for side laps, end laps and cut-offs, so a 36 in roll with a 2 in side lap needs a factor of 36 ÷ 34 = 1.059 for the side lap alone. The sloped area is the footprint times 1 ÷ cos(pitch). The result is rounded up to a whole roll, with a small tolerance so an exact fit does not gain a roll. Area, roll area and overlap are refused if blank, zero (area and roll) or negative; a blank price hides the cost. Laps and product choice come from the manufacturer and the code in force, not from this tool.

Frequently asked questions

Are roofing underlayment calculator results accurate enough to order materials?

They are accurate to the numbers you enter. The result is the roof area plus your overlap, divided by the roll area and rounded up, so it is only as good as the sloped area, the roll size and the lap you enter. Check the final quantity with your supplier, and for a close call such as 11.9 rolls consider one more.

What wastage percentage should I use?

This tool uses one overlap figure for laps and cut-offs together; the default is 15%. A 36 in felt roll with 2 in side laps and 4 in end laps needs about 9% for laps, leaving about 6% for hips, valleys and vents. Use a higher figure for a complex roof. A low-slope double-coverage layout needs about 110%.

Is this tool a substitute for a licensed contractor?

No. It is a planning estimator. Underlayment type, laps and fastening are set by the manufacturer and the building code, and roof work involves fall hazards. Consult a licensed roofer and your local building department for work that affects code compliance or structure.

Can I change the unit prices?

Yes. The price per roll is editable, and you can leave it blank to hide the cost line. Enter the price from your supplier quote to get a total that matches your project.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.