Masonry & Brickwork
Stone Wall Calculator
Stone tonnage for a wall from its face area, thickness and stone density
Updated October 5, 2026 · Live
What this tool does
Works out the weight of natural stone a wall needs from its face area, average thickness and the density of the stone, less an allowance for joints and voids and plus wastage. Gives tonnes and US short tons, the face coverage per tonne and the cost.
Face area times thickness times stone density gives the solid weight; joints and voids come off, wastage goes on, and the result is the stone to order.
People also use
Formula Used
Formula Used
How the stone wall calculator works
Walling stone is bought by weight, and the weight comes from three things you can measure or look up: the face area of the wall, its average thickness, and how heavy the stone is. Area times thickness is the volume of the wall. Multiply that by the density of the stone and you have what a solid block of that size would weigh. No wall is a solid block, though. A mortared wall is partly mortar and a dry stone wall is partly air, so the calculator takes off a share for joints and voids (20% unless you change it) and then adds your wastage allowance. The answer is the stone to order, in tonnes on the metric side and in US short tons of 2,000 lb on the US side, with the other unit shown underneath.
That 20% is our default, not a standard. It is set so the sum agrees with the rule of thumb the UK's Dry Stone Walling Association gives for new work, which is 1 tonne of stone for each square metre of wall. A wall averaging 500 mm (about 20 in) thick in stone of 2,500 kg/m³ comes to 1 × 0.5 × 2,500 × 0.8 = 1,000 kg per square metre of face, or about 205 lb per square foot. Sawn stone laid with thin joints leaves far less than 20% of the wall empty. Rounded fieldstone and cobbles can leave more.
Take a garden wall 10 m long and 1 m high, 300 mm thick, in stone of 2,500 kg/m³. The volume is 10 × 0.3 = 3.00 m³, and a solid block that size would weigh 7.5 tonnes. Less 20% for joints and voids there are 6.00 tonnes in the wall, and with 10% wastage 6.60 tonnes to order, which is 7.28 short tons. At £220 a tonne the stone costs £1,452. On the US side, a wall 27 ft long and 4 ft high has a face of 108 ft². At 12 in thick and 160 lb/ft³ that is 108 ft³ and 17,280 lb solid, 13,824 lb (6.91 tons) in the wall and 7.60 tons to order, or 6.90 tonnes. At $240 a ton it comes to $1,824.77.
Typical stone walling wastage
The calculator adds 10% unless you change it. That figure is our allowance, not a published one, and what you really lose depends on the stone and on who is building. Stone that arrives sorted and roughly squared wastes little. A mixed load of random rubble always has pieces that are the wrong shape, too small to show a face, or that split badly when dressed, and someone building their first wall rejects more than a waller who has built fifty. Allow more for coursed work where stones are trimmed to height, and for a wall with many corners and ends, because those use up the best-shaped stones first.
Keep wastage apart from joints and voids. Wastage is stone you pay for and do not build with. Joints and voids are space in the wall that was never stone. In a dry stone wall much of the breakage is not lost at all, since chips and small pieces go into the middle of the wall as packing. Where stone is being reclaimed from an old wall on site, enter only the area that needs new stone.
What this tool does not do
It gives the walling stone and nothing else. Mortar for a mortared wall is a separate take-off. So are the foundation, any concrete or block backing, the ties for a veneer, the drainage stone and pipe behind a retaining wall, and copings or capstones that are sold by length. It does not design the wall: whether a wall of a given height and thickness will stand, above all one holding back soil, is not something a tonnage can tell you. Thin stone veneer, the sawn product an inch or so (about 25 mm) thick, is sold by the square foot or square metre of face and not by weight, so order that by area. And the calculator knows nothing about prices where you are. The price field is for the figure on your own quote.
On-site considerations for a stone wall
Stone is heavy in a way that is easy to underrate from a number on a screen. A one-foot cube of granite at 160 lb/ft³ weighs 160 lb, about 73 kg, which is more than one person should lift. It arrives tipped loose, in bulk bags or on pallets, and every piece is then moved by hand, so where the load lands matters. Have it dropped along the line of the wall if access allows, and sort it before you start: the biggest stones for the base, long ones set aside to tie the two faces together, flat ones kept back for the top.
Mortared work depends on the weather. In the US the masonry specification TMS 602 brings in cold-weather procedures once the air temperature is 40°F (4.4°C) or below, and the International Masonry Institute's cold-weather bulletin sets out what they involve: heated sand or water, wind breaks, and protection for new work. Other countries set their own thresholds, so follow the local one. Rain will wash out fresh joints, so cover the day's work. A dry stone wall has no mortar to protect and is not held up by the weather in the same way.
Codes and compliance
The rules depend on the country and on what the wall does. A low freestanding garden wall may need no approval, but height limits and planning or zoning rules differ from place to place, so ask locally before building on a boundary. In the United States, the International Residential Code (linked here as adopted in Virginia; states make their own amendments) says in section R404.1.8 that rubble stone masonry foundation walls must be at least 16 in (406 mm) thick and must not support more than 8 ft (2,438 mm) of unbalanced backfill, and it rules them out altogether in the higher seismic design categories. Section R404.4 requires a retaining wall that is not supported at the top and holds back more than 48 in (1,219 mm) of unbalanced fill, or one over 24 in (610 mm) high that resists other lateral loads as well as soil, to be designed in accordance with accepted engineering practice. In England, paragraph 2C7 of Approved Document A says a wall of uncoursed stone in a small building should be at least 1.33 times as thick as the brick or block wall its rules would otherwise ask for. Australia works to the National Construction Code and AS 3700, and Canada to the National Building Code and CSA S304.
Any wall that retains soil, carries part of a building or stands tall beside a path people use should go to a structural engineer before the stone is ordered. The thickness the engineer specifies will move the tonnage far more than any wastage figure.
Before you order
Ask the supplier three things. What is the density of the stone, and is that figure for solid stone or for a loose load? What coverage do they quote? Quarries and stone yards often say how many square metres or square feet a tonne or ton of their stone builds at a stated wall thickness, and the calculator's coverage row can be set against that. If the two disagree, trust the supplier, who knows how their stone packs, and change the joints and voids input until the calculator matches. Last, how is it sold and delivered: loose by the tonne, by the bulk bag or by the pallet, and what does a part load cost?
A single order for the whole job avoids a mismatch: colour varies across a quarry, and a top-up load months later may not look the same. Running half a tonne short and paying a second delivery charge usually costs more than having a little left over.
Adjusting the defaults
Density is the input to check first. The US dimension stone specifications give a sense of the range through their minimum values. ASTM C615 requires granite to be at least 160 lb/ft³ (2,560 kg/m³). ASTM C616 sets 125 lb/ft³ (about 2,000 kg/m³) for sandstone, 150 lb/ft³ (2,400 kg/m³) for quartzitic sandstone and 160 lb/ft³ for quartzite. ASTM C568 sorts limestone into three classes: low density from 110 to 135 lb/ft³ (about 1,760 to 2,160 kg/m³), medium up to 160 lb/ft³, and high above that. The defaults here, 2,500 kg/m³ on the metric side and 160 lb/ft³ (2,563 kg/m³) on the US side, suit granite and the denser limestones and sandstones. A light sandstone at 2,000 kg/m³ is a fifth lighter than the metric default, so the same wall takes a fifth less weight.
Thickness means the average. A wall that tapers from 600 mm at the base to 400 mm at the top goes in as 500 mm, and one that goes from 24 in to 16 in as 20 in. For the area, multiply length by height and take off any openings; the net wall area calculator does the subtraction. Set joints and voids to 0 to see the weight of solid stone, and raise it for rounded stone that packs loosely. Every field can be changed, and the result updates as you type.
Using this stone wall calculator alongside other BuildMetricLab tools
For a mortared wall, the mortar calculator gives a starting figure for the bags, though it is built around brick and block and stone joints are less regular. The gravel calculator covers the drainage stone behind a retaining wall, and the retaining wall calculator handles the concrete for a cast wall where stone is only the facing. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.
Sources & methodology
Wall volume = face area × average thickness. Stone in the wall = volume × stone density × (1 − joints and voids %). Stone to order = stone in the wall × (1 + wastage %). Cost = stone to order × price per tonne (metric) or per US short ton of 2,000 lb (US units). Metric pages take m², mm and kg/m³ and give tonnes; US-units pages take ft², in and lb/ft³ and give short tons (1 short ton = 907.18474 kg, 1 lb/ft³ = 16.0185 kg/m³). The joints and voids default of 20% is our allowance, set so that a wall averaging 500 mm thick at 2,500 kg/m³ gives the Dry Stone Walling Association's guide of 1 tonne per m² of wall; the 10% wastage default is likewise our allowance. Face coverage = wall area ÷ stone to order. Bulk bags (metric) = stone to order ÷ 800 kg, rounded up.
- Dry Stone Walling Association of Great Britain: Frequently asked questions (1 tonne of stone to build 1 square metre of new wall)
- ASTM C615/C615M: Standard Specification for Granite Dimension Stone (minimum density 160 lb/ft³, 2,560 kg/m³)
- ASTM C616/C616M: Standard Specification for Quartz-Based Dimension Stone (minimum density 125, 150 and 160 lb/ft³ for sandstone, quartzitic sandstone and quartzite)
- ASTM C568/C568M: Standard Specification for Limestone Dimension Stone (low, medium and high density classes)
- UpCodes: International Residential Code 2021 (Virginia adoption), R404.1.8 rubble stone masonry foundation walls and R404.4 retaining walls
- GOV.UK: Approved Document A, Structure (2013 edition), paragraph 2C7 walls in uncoursed stone
- International Masonry Institute: Cold Weather Masonry Construction (TMS 602 procedures at 40°F and below)
Frequently asked questions
Are stone wall calculator results accurate enough to order materials?
Close enough to get a quote, and to order once the supplier has confirmed two things: the density of their stone and the coverage they expect from a tonne or ton at your wall thickness. The weight follows directly from area, thickness, density and the joints and voids share, so an error in any of them carries straight through. A stone 10% lighter than the figure you entered means 10% less weight for the same wall.
What wastage percentage should I use?
The default is 10%, which is our allowance and not a published standard. Sorted or roughly squared stone can need less. A mixed load of random rubble, coursed work that needs trimming, a wall with many corners or a first attempt can need more, so try 15% for those. Wastage is separate from the joints and voids input, which covers the part of the wall that is mortar or air.
Is this a substitute for professional advice?
No. It works out a quantity of stone, not whether a wall is safe to build. A retaining wall, a wall that carries part of a building or a tall freestanding wall needs a structural engineer, and local building or planning rules may apply. Enter the thickness they specify and the tonnage will follow from it.
Can I change the unit prices?
Yes. Enter your own price per tonne on the metric side, or per US short ton (2,000 lb) on the US side, and the cost updates. The default is only a placeholder: stone prices vary widely with the type of stone, how much it has been dressed and how far it has to travel.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













