Landscaping & Outdoor
Topsoil Calculator
Work out the volume, weight and cost of topsoil from area and depth
Updated May 13, 2026 · Live
What this tool does
Calculates the volume, weight and cost of topsoil needed to cover a lawn or garden bed at a given depth.
People also use
Formula Used
Formula Used
How the topsoil calculator works
Topsoil is ordered by volume, so the calculator multiplies the area by the depth. In US units the volume in cubic yards is area in square feet × depth in inches ÷ 324, because 12 inches make a foot and 27 cubic feet make a cubic yard (12 × 27 = 324). The weight uses a fixed density of 1,300 kg/m³ (about 2,190 lb/yd³), which is roughly 1.10 short tons per cubic yard.
Take 100 ft² (9.3 m²) at 4 in (102 mm) deep. The volume is 100 × 4 ÷ 324 = 1.23 yd³ (0.94 m³). The weight is about 1.35 tons (2,705 lb, or 1.23 tonnes). At $32 per ton the estimate is $43.28, and that is 2 bulk bags of 1 ton. A bigger lawn of 1,000 ft² at 6 in (150 mm) needs 18.52 yd³, about 20.29 tons, which is $649.25 at the same price and 21 bulk bags.
Typical US landscaping and outdoor wastage
The calculator has no wastage field, so allow for it yourself. Topsoil settles and firms after spreading, and uneven ground takes more than a flat measurement suggests. A common allowance is 5 to 10% more than the calculated volume, which is a trade rule of thumb and not a figure from a standard. For the 100 ft² example, 10% extra is 1.36 yd³ instead of 1.23 yd³. Penn State Extension quotes its recommended depth as a firmed or settled depth, so order enough to end at that depth after rolling or watering in.
Round up to a load that the supplier can deliver. Many suppliers sell by the cubic yard with a minimum delivery, so check that before you work out the cost.
What this tool does not do
It does not replace a professional quote, adjust for local prices, test your soil or grade your site. It multiplies an area by a depth and a density. It does not tell you whether the soil is suitable for the plants you want, whether the ground needs drainage, or what the supplier's soil contains. Those remain the responsibility of a suitably qualified designer, a soil testing lab or your local building official.
On-site considerations for topsoil
Depth depends on the job. Penn State Extension advises a minimum of 4 to 6 in (100 to 150 mm) of good-quality firmed topsoil to establish a quality lawn, with about 2 in worked into the top of the subsoil so there is a gradual change between layers. New planting beds usually need more than lawns. The UK Royal Horticultural Society (RHS) gives at least 10 cm (4 in) for laying a lawn and about 20 cm (8 in) or more for new beds. An 8 in bed over 100 ft² is 100 × 8 ÷ 324 = 2.47 yd³ (about 2.7 tons).
Grade the ground to slope gently away from buildings. Penn State suggests a fall of 1 to 4%, which is 1 to 4 ft in every 100 ft. Keep the finished soil level below any siding, sill or weep holes so that soil does not hold water against the wall. Topsoil is heavier when wet, so the weight shown is for ordinary moist soil. A wet delivery can weigh noticeably more than the same volume dry.
Codes and compliance
There is no building code for buying topsoil, but changing the grade can have rules attached. Large grading jobs, retaining walls and changes to how water drains off the lot can need a permit from your city or county, and stormwater rules often apply near property lines and watercourses. If you are unsure, ask your local building department before you start, because early clarity is cheaper than a corrective inspection. Rules differ by state and municipality, and outside the United States they are different again.
Before you order
Check the soil before you buy. The RHS buying guide advises looking for stones, thick roots, weeds and contaminants such as glass and brick, and asking the supplier where the soil comes from, because soil from building sites can vary a lot in quality. It describes three grades (premium, general-purpose and economy), which is a UK system with a standard behind it (BS 3882). In the United States, grades vary by supplier, so ask for a description or a lab test and compare like with like. Ask whether the price is per cubic yard or per ton, because the two are not interchangeable. The price field here is per short ton of 2,000 lb.
Adjusting the defaults
Every input is editable: the area, the depth and the price per ton. Measure the area as length times width, and split an irregular bed into rectangles. Enter the depth after settling. The pre-filled depth is a typical lawn depth and the price is a placeholder, so replace both with your own. Use the unit switch at the top of the page to work in feet and inches or in metres and millimetres. A blank price leaves the cost out, and a blank or zero area or depth is refused.
Using this topsoil calculator alongside other BuildMetricLab tools
Use the volume and weight with the gravel, mulch, sand and compost calculators to plan a whole bed or lawn. For a raised bed, the raised bed soil calculator works from the bed's length, width and height and gives a bag count. The results can also be sent to the PlainEstimate hand-off to be priced. All BuildMetricLab tools run entirely in your browser, with no sign-up and nothing sent to a server, and every formula is shown on the page so you can check the maths.
Sources & methodology
Volume (yd³) = area (ft²) × depth (in) ÷ 324, where 324 = 12 in per ft × 27 ft³ per yd³. Weight = volume × 1,300 kg/m³ (about 1.10 short tons per yd³; 1 yd³ = 0.764555 m³). Cost = weight in short tons (2,000 lb) × price per ton. Bulk bags are counted at 1 ton each, rounded up. The density is a fixed assumption for moist topsoil; real soil varies with texture, organic matter and moisture. A blank price drops the cost row; zero, negative or blank area or depth is refused.
Frequently asked questions
Are topsoil calculator results accurate enough to order materials?
The volume is exact arithmetic for the area and depth you enter, but the weight assumes a standard density of 1,300 kg/m³ (about 1.10 tons per cubic yard) and real soil varies with moisture and texture. Use the result as a starting estimate and confirm the quantity and the unit of sale with your supplier before ordering.
What wastage percentage should I use?
This calculator has no wastage field. Topsoil settles after spreading, so many landscapers add 5 to 10% to the volume, which is a rule of thumb and not a standard. Raise the depth or the area slightly before calculating. Penn State Extension's recommended depth is a settled depth, so allow for that.
Does this replace professional advice?
No. This tool only produces a planning estimate. For work that affects drainage, grading near a property line, retaining walls or building code compliance, consult a licensed contractor or design professional before proceeding.
Can I change the unit prices?
Yes. The price field is per short ton of 2,000 lb. If your supplier quotes per cubic yard, multiply the yard price by 0.9 to get a rough price per ton (1 yd³ is about 1.10 tons), or compare the cost row against the quote.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













