BuildMetricLab

Landscaping & Outdoor

Gravel / Aggregate Calculator

Gravel volume, weight and cost from area and depth

Updated May 13, 2026 · Live

What this tool does

Estimates the volume, weight and cost of gravel or crushed stone for a path, drive or bed from its area and depth.

Estimates gravel volume in cubic yards, weight in tons and cost from the area and depth you enter.

Inputs
ft²
in
$
Result

Gravel Required

2.08 tons

Volume
1.54 yd³
Bulk Bags (1,653 lb)
3
Estimated Cost
$114.45
Price it on PlainEstimate

Opens these materials as a new estimate on PlainEstimate, our free estimate and invoice app.

Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
V=A⋅d,W=V⋅ρV = A \cdot d,\quad W = V \cdot \rho
VV
Gravel volume
AA
Surface area
dd
Layer depth
WW
Gravel weight
ρ\rho
Bulk density, about 1.35 tons per yd³ (1.6 t/m³)

How the gravel / aggregate calculator works

Gravel is ordered by the cubic yard or by the ton, and the volume you need is the area multiplied by the depth. This calculator takes the area in square feet and the depth in inches, works out the volume in cubic yards, then converts it to tons with an average bulk density. The formula is V = A × d for volume and W = V × ρ for weight, with the cost the weight times your price per ton. Volume in cubic yards is area (ft²) × depth (in) ÷ 12 ÷ 27, because 12 in make a foot and 27 ft³ make a cubic yard.

Example with the defaults: 250 ft² at 2 in deep is 250 × 2 ÷ 12 = 41.67 ft³, which is 1.54 yd³ or 1.18 m³ (23.2 m² at 50.8 mm). At 1.35 tons per cubic yard that weighs 2.08 tons, or 1.89 tonnes. At $55 per ton the cost is $114.45.

A driveway of 1,000 ft² at 4 in deep is 1,000 × 4 ÷ 12 ÷ 27 = 12.35 yd³, or 9.44 m³. That weighs 16.65 tons (15.1 tonnes) and costs $915.61 at the same price. A path 3 ft wide and 40 ft long is 120 ft², and at 3 in deep it needs 30 ft³, which is 1.11 yd³ or 1.50 tons.

Typical US landscaping and outdoor wastage

The tool adds no allowance, because the right figure depends on the ground. Loose gravel settles when it is spread and compacted, and some is lost to uneven subgrade and spillage. Installers commonly order 5 to 15% more, a trade habit and not a published standard. On the 2.08 ton example, 10% extra is 2.29 tons. A firm, flat base needs less than soft or uneven ground.

Depth is the other big lever. A 1 in error in depth on 250 ft² changes the volume by 0.77 yd³, which is about half the 2 in answer. Measure the depth at several points, because ground is rarely level.

What this tool does not do

It does not design a base, size the stone, or check drainage. It does not include the sub-base, geotextile, edging, delivery charges or the cost of spreading and compacting. It uses a single density for every stone type, so it is not a substitute for a supplier's weight per cubic yard. It is not a substitute for a quote or for the advice of a qualified contractor.

On-site considerations for gravel / aggregate

Stone size and depth go together. A common rule of thumb is a layer at least about twice the diameter of the largest stone, so 3/4 in (20 mm) stone wants about 1.5 in (40 mm) or more, and loose decorative gravel is often laid 2 to 3 in deep. A driveway usually needs a compacted sub-base under a surface layer, and the tool's volume covers one layer, so run it again for each layer.

Weed-suppressing geotextile under the gravel and edging around it keep the stone in place and out of the lawn. Gravel is a permeable surface, so water soaks through it, and the US EPA describes permeable pavements as letting rain seep to layers of soil and gravel below. Slope the surface away from buildings, because gravel does not shed water the way pavement does.

Codes and compliance

Spreading gravel on a garden path or bed does not normally need a permit. A new driveway, a change of access onto a public road, or a large hard surface can need approval or fall under stormwater rules that differ by region, so ask your local authority before you start. Work near a foundation, a retaining wall or a drain should follow local building code and a designer's advice. The tool gives a quantity, not a design.

Before you order

Ask your supplier for the weight per cubic yard of the exact product, because bulk density depends on the rock, the size grading and the moisture. If it differs from 1.35 tons per yd³, scale the tool's weight in proportion. A 1.50 tons per yd³ stone makes the default 2.31 tons instead of 2.08. Compare delivered prices per ton, and ask about minimum load size. Bulk ordering by the yard or ton is usually cheaper than bags, and bags suit only small areas.

Adjusting the defaults

Every input is editable. The area and depth must be above zero. A blank or zero field is refused instead of quietly using a default, and a blank price hides the cost line. For an irregular area, split it into rectangles and add them. If a supplier quotes by the cubic yard instead of the ton, multiply the cubic yard price by the volume shown.

Using this gravel / aggregate calculator alongside other BuildMetricLab tools

Pair this estimate with the topsoil, mulch and sand calculators for the beds around it. All BuildMetricLab tools run in your browser. Nothing you type is sent anywhere, and every formula is shown on the page so you can audit the maths.

Sources & methodology

Volume is area × depth: the page takes area in ft² and depth in inches, and calculates cubic yards as area × depth ÷ 12 ÷ 27 (1 yd³ = 27 ft³ = 0.7646 m³). Weight is volume × a bulk density of 1.6 tonnes per cubic metre, which is 100 lb/ft³ or about 2,700 lb/yd³, or about 1.35 short tons (2,000 lb) per cubic yard. The tool uses this single density for every stone type; pea gravel is typically near it, while crushed stone and wet material can be heavier. Cost is tons × price per ton, hidden if no price is entered. The bulk bag count is the weight divided by 750 kg (1,653 lb), rounded up. Area and depth must be above zero and the price zero or more. The tool applies no wastage or compaction factor.

Frequently asked questions

Are gravel / aggregate calculator results accurate enough to order materials?

They are a sound starting quantity. The volume is exact for the area and depth you enter, but the weight uses one average density of about 1.35 tons per cubic yard (1.6 t/m³). Crushed stone and wet gravel can weigh more, so confirm the figure with your supplier. Add an allowance for compaction and spillage, then round up to the load size the supplier delivers.

What wastage percentage should I use?

The tool adds no wastage. Loose gravel settles when it is spread and compacted, and some is lost to uneven ground, so many installers order 5 to 15% extra. That is a trade habit, not a published standard. For the default 2.08 tons, 10% extra is 2.29 tons. Use the lower end for a flat, firm base and the higher end for soft or uneven ground.

Does this replace professional advice?

No. It estimates quantity and cost only. It does not design a base, check drainage or confirm that the work is allowed. For driveways, retaining walls, work near a foundation or any drain, consult a licensed contractor or design professional.

Can I change the unit prices?

Yes. The price per ton is editable, and a blank price hides the cost line so only the quantity shows. A price of zero is accepted if the gravel is free. The area and depth must be above zero.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.