Masonry & Brickwork
Quoin / Corner Brick Calculator
Quoin bricks from wall height, course height, corners and the bricks each course of the quoin takes, with waste and cost
Updated October 9, 2026 · Live
What this tool does
Counts the corner bricks a quoin detail needs: courses from the wall height and the course height (brick plus joint, 75 mm for a UK brick, 2 2/3 in for a US modular brick), times the bricks per course your quoin pattern uses, times the corners, with a waste allowance and the cost. Metric or US units.
Wall height over course height, rounded up, times bricks per course times corners, plus waste.
People also use
Formula Used
Formula Used
How the quoin brick calculator works
A quoin is the corner brick of a course, the first brick laid at each angle of a wall, and when quoins are picked out in a different brick, a different colour or a projecting course they become the detail this calculator counts. The Clay Brick Association's glossary has the plain definition: "Corner brick, the first brick of each course at the corner", and notes that brick quoins may stand proud of the facing brickwork and that decorative quoins can be brick, stone or concrete. The count is courses times bricks per course times corners. Courses come from the wall height divided by the course height, which is the brick plus one bed joint, rounded up because a part course is still laid; bricks per course per corner is the pattern you are building, two for the common quoin where a stretcher shows on one face and a header on the other; and the corners are how many angles the detail runs up. Add a waste allowance and the result is the number of special bricks to order.
The course height is the figure that trips people up, because it is not the brick height. In the UK a standard brick is 215 by 102.5 by 65 mm and the Brick Development Association's guide to designing to brickwork dimensions gives the coordinating size with a nominal 10 mm joint as 225 by 112.5 by 75 mm, so a course is 75 mm and a 2.4 m wall is exactly 32 courses. In North America the Brick Industry Association's Technical Note 10 sets out modular coursing: a modular brick is nominally 2 2/3 in high including its joint, so "three courses (three brick and three mortar joints)" make 8 in and an 8 ft wall is 36 courses, the brick itself being specified at 2 1/4 in with the joint taking up the rest; the engineer modular brick runs five courses to 16 in, 3.2 in a course; a standard brick at 2 1/4 in with a 1/2 in joint is 2 3/4 in. Australian bricks are commonly 76 mm high with a 10 mm joint, 86 mm a course. Enter the course height your brick gives, and the Height of Whole Courses row shows how far the rounded-up count reaches.
How many bricks a quoin takes
In plain stretcher bond the corner brick is one brick turned through 90 degrees: a stretcher on the front and a header on the return, alternating course by course so the bond continues round. That corner brick alone is one per course. Two per course gives a quoin a full stretcher long on both faces, the corner brick plus the brick beside it on the return, which is the usual width for a quoin picked out in a contrasting brick; enter one if only the corner brick itself is the special. Projecting or toothed quoins, the long-and-short pattern that steps in and out course by course, use more: a quoin two bricks long on one face and one on the other is three per course, and the BDA's aesthetic brickwork guide, citing PD 6697, puts the maximum projection of a header in the outer leaf at a third of the brick's thickness, 34 mm, so projecting quoins in a cavity wall are shallow. Set the bricks per course to match the drawing, not the default.
Worked examples
The metric default is a 2.4 m single-storey wall at 75 mm courses with four corners and two bricks per course: 32 courses, 64 bricks a corner, 256 bricks, 269 with 5% waste, £672.50 at £2.50 a brick. The US default is an 8 ft wall at the 2.67 in modular course: 36 courses (the row shows 36.0, so no part course), 72 a corner, 288 for four corners, 303 with waste, $303 at a dollar each. A two-storey gable end 5.4 m high with six external corners and a three-brick projecting quoin is 72 courses and 1,296 bricks, 1,361 with 5%; the same in feet, 20 ft at 2.67 in with six corners and three per course, is 90 courses and 1,620 bricks, 1,701 with waste, $2,041.20 at $1.20. Rounding matters on odd heights: a 9 ft wall at a 2.75 in standard course is 39.3 courses, so 40, and the whole courses reach 9.17 ft; an Australian 2.7 m wall at 86 mm is 31.4 courses, 32, reaching 2.75 m. The last course is cut to the plate either way, but its quoin brick is still a full brick.
Waste and ordering
Five percent is the usual brickwork allowance for breakage and cuts, and quoins deserve at least that, because a chipped arris on a contrasting brick shows where a chipped field brick would not, and the cut closers that keep the bond beside a quoin come out of the same pack. Raise it to 10% for a soft or handmade brick, for a projecting detail where every corner is cut, or where the quoin brick is a special that cannot be reordered from stock in the same batch. Specials and contrasting bricks are often sold by the pack of a few hundred, so round the total up to the pack and keep the spares; a quoin replaced later from a different firing will not match. The waste row is applied to the whole count, and the price is on the bricks bought.
What the calculator leaves out
It counts the corner bricks only. The field bricks of the wall, including the ones the quoins replace, belong to the brick calculator, and if the quoins are the same brick as the wall there is nothing extra to buy at all: the count here is the number already inside the wall area. It does not count closers, the quarter or three-quarter bricks cut to carry the bond past the quoin, which depend on the bond and the quoin length. It does not know the openings: a corner that stops at a door head needs fewer courses than the wall height, and a quoin that runs only to a string course needs its own height entered. And it says nothing about structure; a projecting quoin on a cavity wall is a design detail for the designer and the wall ties around it are counted separately.
Using this with other BuildMetricLab tools
Measure the wall with the net wall area calculator, count the field bricks and mortar with the brick calculator, add the quoins from here, and the brick arch calculator covers the heads of the openings between the corners. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.
Sources & methodology
Courses per corner = ⌈wall height ÷ course height⌉, course height being the brick height plus one bed joint (75 mm for a UK 65 mm brick with a 10 mm joint, coordinating size 225 × 112.5 × 75 mm per the Brick Development Association; 2 2/3 in for a US modular brick, three courses to 8 in, 3.2 in for engineer modular and 2 3/4 in for standard, per BIA Technical Note 10). Quoin bricks = courses × bricks per course per corner × corners; bricks to buy = that × (1 + wastage %), rounded up; cost = bricks to buy × price. Bricks per course is the visitor's pattern: 2 for a stretcher-and-header quoin, more for projecting or long-and-short quoins. Field bricks, closers and ties are not included.
- Brick Development Association, Designing to Brickwork Dimensions, Technical Guide (2023): standard brick 215 × 102.5 × 65 mm, 10 mm nominal joint, coordinating size 225 × 112.5 × 75 mm
- Brick Development Association, Aesthetic Brickwork, General Guide (2023): projecting brickwork, maximum header projection in a half-brick leaf about a third of the thickness (34 mm)
- Brick Industry Association, Technical Note 10, Dimensioning and Estimating Brick Masonry: modular coursing, three courses to 8 in, engineer modular five courses to 16 in
- Clay Brick Association, Know Your Building Terms: quoin as the first brick of each course at the corner; course, closer, header and stretcher
Frequently asked questions
Are quoin / corner brick calculator results accurate enough to order materials?
Yes, if the course height is the real one for your brick and joint and the bricks per course matches the quoin pattern on the drawing. The courses are rounded up so a part course still gets its quoin brick, and the waste allowance covers chips and cuts. Check the pack size: contrasting and special bricks are sold by the pack, and a later top-up from another batch will not match.
What wastage percentage should I use?
The default is 5%, the usual brickwork allowance, applied to the whole count and rounded up. Use 10% for soft or handmade bricks, for projecting quoins where every corner is cut, or where the quoin is a special that cannot be reordered to match. Set it to 0 to see the bare count.
Is this a substitute for a licensed contractor or engineer?
No. It counts bricks for a corner detail. Whether a quoin can project, how the bond is kept beside it and what the wall ties and lintels around it need are matters for the designer and the building code; for anything affecting structure, gas, electrics, plumbing or drainage to a public sewer, use a suitably qualified professional.
Can I change the unit prices?
Yes. The price per brick is yours, from the merchant's listing for the quoin brick, and the cost is the bricks bought, including the waste allowance, at that price. Enter 0 to see the count only.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













