Wall & Ceiling
Crown Molding Calculator
Crown moulding or coving lengths from the ceiling perimeter, with corner joints and the flat-cut mitre and bevel for the spring angle
Updated October 10, 2026 · Live
What this tool does
Counts the lengths of crown moulding or plaster coving a room needs from the ceiling perimeter, a wastage allowance and the piece length, counts the inside and outside corner joints, and gives the compound mitre saw settings for cutting flat at the moulding's spring angle, 31.6° mitre and 33.9° bevel for 38° crown. Results in feet and metres with the cost at your price per length.
Perimeter plus wastage, divided by the piece length and rounded up; saw settings from the spring angle.
People also use
Formula Used
Formula Used
How the crown moulding calculator works
Crown moulding and plaster coving are sold by the length, so the count is the perimeter of the ceiling, plus an allowance for the offcuts at each mitre, divided by the length of one piece and rounded up. The calculator does that sum, then counts the corner joints from the number of inside and outside corners you enter and gives the saw settings for cutting them. Inside corners are coped or mitred and outside corners are mitred; Lowe's crown moulding installation guide puts it as "Inside corners: Coping or miter cuts. Outside corners: Compound miter cuts", with a 45° cut on each piece when the moulding is held in position against the fence. The saw settings for cutting flat on the table come from the spring angle, the angle the moulding leans off the wall. JLC's step-by-step crown article gives the pair for the common 38° crown: "the saw is beveled to 33.9 degrees and the miter is moved to 31.6 degrees", settings that "are usually highlighted on a saw", and notes that 45° and 52° profiles "sit higher up the wall" and need different settings. The WoodWeb knowledge base lists the same pairs: 33.9° bevel and 31.6° mitre for 38/52 crown, 30.0° bevel and 35.3° mitre for 45/45 crown. The calculator derives them from the geometry for a 90° corner, mitre = atan(sin S) and bevel = asin(cos S × cos 45°), where S is the spring angle, and gets 31.6° and 33.9° at 38°, 35.3° and 30.0° at 45°, and 38.2° and 25.8° at 52°.
With the US default, a 50 ft perimeter in 8 ft lengths with 10% wastage, the run is 55.0 ft and the count seven lengths, 56 ft bought; with four inside corners that is four coped or mitred joints. The metric default, 14 m of 3 m plaster cove at 10%, is 15.4 m and six lengths, 18 m bought. The 10% is a starting allowance; the Ledgendary Crown installation guide says to "add all of the wall lengths together" and "add 15% for cutting mistakes and waste", and a room with many corners or a patterned profile is nearer that figure.
Coping, mitring and the joints along a wall
The choice at an inside corner is between a cope, where one piece is cut square to the wall and the other is cut to its profile, and a mitre, where both are cut at 45°. JLC explains why trim carpenters prefer the cope: "a coped joint on the inside corners should separate less over time. With only one cut edge meeting the profiled face, the shrinkage from only one length of crown will show". Fine Homebuilding adds that a cope cut to the correct ceiling projection "is forgiving and fits every time", and that the stock is primed on all sides and kept as close as possible to the home's living conditions rather than in a garage or basement, so it does not move after fitting. This Old House lists the four cuts a room needs, "a coped corner joint, an outside miter, a square cut, and a scarf joint", and where joists run parallel to the wall its general contractor nails the crown to angled blocking rather than into the ceiling. The scarf joint is the one the calculator cannot count: it is needed wherever a wall is longer than a piece, so a long wall in 8 ft lengths has one or two along it, and the spare from the wastage allowance is what the scarf and the practice cuts come out of.
Plaster cove in the UK
In the UK the usual product is a gypsum plaster cove rather than a timber crown. British Gypsum's Gyproc Cove 127 is listed by Jewson as a 127 mm wide, 3,000 mm long C-profile gypsum cove, which is why the metric default piece is 3 m. It is fixed with a gypsum cove adhesive: the Siniat cove adhesive data sheet gives 5 kg and 12.5 kg bags, a working time of 45 to 65 minutes, about 3.3 litres of water per 5 kg bag, and installation in accordance with BS 8212 and BS 8000-8. The adhesive is not counted here because the data sheet gives bag sizes and mixing water but no coverage per metre of cove. Plaster cove is cut in a mitre box rather than on a compound saw, so the flat-cut settings on this page are for timber and MDF crown.
What this tool does not do
It counts lengths and corners for one continuous run. It does not plan which wall each piece goes on, count scarf joints, allow for a pattern repeat on a decorative profile, or price adhesive, nails, filler and paint. It does not handle corners other than 90°; a bay or a splayed wall needs the angle measured and the settings taken from a chart or the saw's own table, which both JLC and the Ledgendary guide describe doing with a protractor at each corner.
Adjusting the defaults
Every input is editable. The perimeter is measured at ceiling level along every wall, including the returns into bays and chimney breasts, without deducting doors and windows, since the moulding runs over them. The piece length is what the supplier sells, such as the 3 m plaster cove above; a wall longer than one piece needs a joint along it. The corner counts are the inside and outside corners of the room; a plain rectangle has four inside corners and a chimney breast adds two outside and two inside. The spring angle is on the moulding's label or measured off a sample, 38° for most US crown, 45° for a cove with equal wall and ceiling projections and some crown, 52° for the profiles that sit flatter to the ceiling. Outside the United States and the United Kingdom the same count applies, with the piece length and spring angle of the local product. Wastage starts at 10%, with the 15% a maker suggests for a first job; the price per length gives the cost, and zero shows quantities only.
On-site considerations
The two things that spoil a crown job are the corners and the fixings. Corners are rarely a true 90°, so the cut is tested on an offcut first, which is one more reason for the allowance; the Ledgendary guide has the fitter cut two short pieces as templates before starting. Fixings go into studs or ceiling joists, found with a stud finder and marked before the moulding goes up, at the 16 to 18 in spacing Lowe's gives; where there is nothing to nail to, blocking goes in first. Plaster cove goes on adhesive and is supported until the adhesive sets, and the mitres are filled and sanded before painting.
Using this alongside other BuildMetricLab tools
Run the chair rail round the same room with the chair rail calculator, count the boards with the drywall calculator, and paint it all with the paint calculator. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.
Sources & methodology
Lengths = ceiling perimeter × (1 + wastage %) ÷ piece length, rounded up; bought length = lengths × piece length; corner joints = inside corners + outside corners. Flat-cut saw settings for a 90° corner from the spring angle S: mitre = atan(sin S ÷ tan 45°), bevel = asin(cos S × cos 45°); cut in position, 45° mitre. US inputs in ft are converted to m first; results show both. References: JLC, Crown Molding Step by Step (38° crown: bevel 33.9°, mitre 31.6°; 45° and 52° profiles; cope versus mitre); Ledgendary Crown installation guide (add 15% for cutting mistakes and waste; 38° spring angle, mitre 31.6°, bevel 33.9°); Lowe's moulding installation guide (inside corners coped or mitred, outside corners compound mitred, 45° cuts in position, nails every 16 to 18 in into studs); Fine Homebuilding (coping to the ceiling projection); This Old House (joint types, blocking); WoodWeb (38/52 and 45/45 settings); Jewson listing of Gyproc Cove 127, 3,000 mm; Siniat cove adhesive data sheet (5 and 12.5 kg bags, BS 8212 and BS 8000-8).
- JLC (Journal of Light Construction), Crown Molding, Step by Step, March/April 2025: cutting on the flat with the saw bevelled to 33.9° and mitred to 31.6° for 38° crown, 45° and 52° profiles needing different settings, cope versus mitre at inside corners
- Ledgendary Crown, installation guide (Home Depot copy): add all wall lengths together and add 15% for cutting mistakes and waste; 38° spring angle, mitre 31.6° and bevel 33.9° to the left; protractor at each corner and templates before cutting
- Lowe's, Moulding Installation Guide, Crown: inside corners coped or mitred, outside corners compound mitred, opposing 45° cuts, nails into studs every 16 to 18 in
- Fine Homebuilding, The Secret to Coping Crown Molding: coping to the ceiling projection so the joint fits every time; storing moulding in conditioned space
- This Old House, How To Put In Crown Molding: coped corner joint, outside mitre, square cut and scarf joint; angled blocking where joists run parallel to the wall
- WoodWeb knowledge base, Finding Compound Angles for Crown Moulding: 38/52 crown bevel 33.9° and mitre 31.6°, 45/45 crown bevel 30.0° and mitre 35.3°
- Jewson, British Gypsum Gyproc Plaster Coving 3000 x 127 mm: C-profile gypsum cove, product width 127 mm, product length 3,000 mm
- Siniat (Etex), Cove Adhesive technical data sheet: gypsum-based adhesive in 5 kg and 12.5 kg bags, working time 45 to 65 minutes, about 3.3 litres of water per 5 kg bag, used in accordance with BS 8212 and BS 8000-8
Frequently asked questions
Are crown molding calculator results accurate enough to order materials?
Yes, as a count of lengths. The perimeter plus the wastage allowance, divided by the piece length and rounded up, is how a trim carpenter prices a room, and the maker's guide quoted on this page does the same sum with 15% added. What the count does not know is which wall each piece goes on, so a long wall that needs a scarf joint, or a corner that takes two attempts, comes out of the allowance; a room with many corners or a patterned profile is safer at 15%.
What wastage percentage should I use?
10% is the starting point and 15% is what the Ledgendary Crown guide tells first-time fitters to add for cutting mistakes and waste. The losses are the offcut at every mitre, the test cuts on an out-of-square corner, a miscut on a profile that cannot be turned round, and the short end left when a wall is not a whole number of pieces. A simple rectangle in long lengths wastes less; many corners, short lengths or a pattern repeat waste more.
Does this replace professional advice?
No. It is a quantity and cutting-angle estimate from the values you enter. The saw settings are for a 90° corner and the moulding's nominal spring angle; a real corner is measured and the cut tested first. Fixing into studs and joists, and anything that touches structure, fire separation, gas, electrics, plumbing or drainage to a public sewer, is for a suitably qualified professional.
Can I change the unit prices?
Yes. The price is per length of the size you enter, and the cost row is that price times the number of lengths, so it follows the product you intend to buy. Adhesive, nails, filler and paint are not priced here. Leave the price at zero to see quantities only.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













