Windows & Doors
Flyscreen Calculator
Mesh length off the roll and spline for flyscreens, from screen frame size and roll width
Updated October 1, 2026 · Live
What this tool does
Works out how much insect screen mesh to cut from a roll for a set of windows or doors, allowing for the wrap into the spline channel and nesting narrow pieces across the roll, plus the spline to hold them.
Frame plus wrap on each side, laid across the roll in as many rows as the screens need; spline is the perimeter.
People also use
Formula Used
Formula Used
How the flyscreen calculator works
Insect mesh is sold off a roll of fixed width and cut to length. The useful question is not how many square metres you need but how long a piece to buy and whether it fits the roll. The calculator takes the screen frame size, adds a wrap allowance on every side so the spline can trap the mesh in its channel before you trim the excess, and tries the piece both ways round. Whichever way fits the roll and buys the least length wins, with narrow pieces nested side by side. The result is the length to cut from the roll for all the screens, plus the spline needed to hold them in.
The metric default is one 900 × 1,200 mm frame with a 25 mm wrap on a 1,220 mm roll. The piece is 950 × 1,250 mm; only the 950 mm side fits across the roll, so you buy 1.25 m. The spline is the perimeter, 2 × (900 + 1,200) = 4.2 m. With US units, a 36 × 48 in window with a 1 in wrap on a 48 in roll is a 38 × 50 in piece, so 50 in, or 4 ft 2 in, off the roll. The spline is 2 × (36 + 48) = 168 in, or 14 ft. Six small 500 × 800 mm frames with the same 25 mm wrap show the nesting. The 550 mm pieces go two across a 1,220 mm roll, so three rows of 850 mm, 2.55 m in all, rather than six rows and 5.1 m. Turning the piece can matter even when it fits either way. One 1,100 × 700 mm frame on the same roll, same wrap, is a 1,150 × 750 mm piece, and laying the 1,150 mm side across the roll buys 0.75 m instead of 1.15 m.
Why the wrap allowance matters
You cannot cut mesh to the exact size of the frame. It is laid over the channel, the spline is rolled in, and it is the spline going in that tensions the mesh; the surplus is trimmed afterwards with a knife along the channel. An inch, or 25 mm, on each side is the usual figure; some fitters use more on big doors. The allowance is what makes a 1,200 mm frame a 1,250 mm piece, and that extra 50 mm is why a 1,220 mm roll will not cover it. When the calculator says a piece will not fit, the choices are a wider roll or a join, which shows and weakens the panel.
Roll widths and mesh types
Roll widths follow the old imperial sizes almost everywhere. Australian flywire comes on 30 m rolls, with 910 mm and 1,220 mm the common widths and wider rolls for doors. In the US and Canada, screening is sold in widths from 24 in up to 108 in, with 36 in, 48 in and 72 in the sizes most shops keep. UK suppliers sell the same product by the metre from 1.2 m rolls, usually as fly screen or insect mesh. Standard fibreglass suits most windows. Aluminium is stiffer and better for doors; pet-resistant mesh is a heavy vinyl-coated polyester; fine no-see-um mesh has a tighter weave for midges and sandflies; and solar screening cuts glare. Stock sizes change by brand, so check the roll before you rely on a width.
Bushfire-prone parts of Australia have their own rule. The National Construction Code, Part H7 sends houses in designated bushfire-prone areas to AS 3959 (or the NASH steel-framing standard). Where screens are fitted under AS 3959 they must be corrosion-resistant steel, bronze or aluminium mesh with openings no larger than 2 mm, and at the highest level, BAL-FZ, steel or bronze only. Fibreglass flywire does not meet it. The calculator's maths is the same for ember mesh; only the product changes.
Spline
Spline is the rubber or vinyl cord that holds the mesh. Phifer's spline size guide lists diameters from 0.125 in (3.2 mm) to 0.250 in (6.4 mm). The rule is to match the width of the groove in the frame, dropping one size for the thicker fabrics, PetScreen, TuffScreen and the solar screens; for the same groove, Phifer's frame chart also lists aluminium one size under fibreglass. Australian splines run through a similar range of about 4 to 6 mm. The calculator gives the spline as the perimeter of each frame added up; buy the next whole roll above it, and keep the old spline to size the new one against.
Measuring
Measure the screen frame the mesh will be fixed to, not the glass and not the wall opening. On a fixed screen that is the outside of the frame channel; on a sliding door it is the screen panel; on a retractable screen it is the cassette and track length the maker specifies. Measure each frame at two points, because old frames are rarely square, and use the larger figure. Group frames of the same size and run the calculator once per group; different sizes nest differently, so adding them as one count would be wrong. Stick-on kits, the hook-and-loop or magnetic strips sold for rented flats and sash windows, have no spline channel: measure the window frame the strip will sit on, treat the wrap as the overlap onto it, and ignore the spline rows.
What the length does not include
Frame sections, corner stakes, pull tabs, rollers for sliding screens and fixings are separate. The mesh length is the length to cut, not a whole roll; the PlainEstimate line rounds it up to the next 0.1 m or whole foot. When pieces fill the roll width exactly, allow a few millimetres for a straight cut. The window area calculator gives the glass area for a whole house if you are pricing screens by area, and the door rough opening calculator gives the frame sizes a screen door has to match. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.
Sources & methodology
Piece = (frame width + 2 × wrap) × (frame height + 2 × wrap). For each way round whose across-the-roll side fits: pieces across = floor(roll width ÷ across side), rows = ceil(screens ÷ pieces across), length = rows × the other side. The way round with the shorter length is used; if neither fits, the calculator stops and says so. Mesh area = piece area × screens. Spline = 2 × (width + height) × screens.
Frequently asked questions
Are flyscreen calculator results accurate enough to order mesh?
Yes, provided the frame is measured at the spline channel and the roll width is what you are buying. The length already includes the wrap on every side, the better way round for the piece and the nesting of narrow pieces; the PlainEstimate line rounds it up to the next 0.1 m or whole foot.
How much wrap allowance should I use?
25 mm (1 in) on each side is the usual figure, trimmed off after the spline is in. Use more on a large door panel or if you are new to it.
Does this replace professional advice?
No. It sizes mesh and spline. Made-to-measure and retractable screens are measured by the supplier, and in a designated bushfire-prone area in Australia the mesh itself is specified by AS 3959 under the National Construction Code, so check the product before you buy.
Does it tell me which roll to buy?
It tells you whether the piece fits the roll width you enter, which way round to lay it, and how much length to cut, and it stops with a message if the piece is too wide either way. Change the roll width to the next size the shop stocks and run it again.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













