Windows & Doors
Window Sill Calculator
Window sill, stool or window board length from the opening width and the horns, with weight and cost
Updated October 5, 2026 · Live
What this tool does
Works out the length of a window sill, stool or window board from the opening width plus a horn at each end, for one window or several, with a cutting allowance, the weight of a stone or concrete sill and the cost per metre or foot.
Opening width plus two horns gives the sill length; the number of windows and a cutting allowance give the total to buy, its cost and the weight of each stone or concrete sill.
People also use
Formula Used
Formula Used
How the window sill calculator works
A sill is nearly always longer than the window above it. The extra at each end is the horn, and the whole sum is one line: opening width plus two horns. The calculator does that for one window, multiplies by the number of windows, adds a cutting allowance if you want one, and prices the total by the metre or the foot. For a stone or concrete sill it also gives the weight of each piece.
The same sum serves three different things. Outside, a lug sill in stone, cast stone or concrete has its ends built into the masonry on each side of the opening, and the horn is the length built in. A slip sill is fitted between the jambs after the wall is up, so its horn is 0. Inside, the board is called a stool in the US and a window board in the UK, and its horns run sideways along the wall under the side casings. Fine Homebuilding describes the horn as the part of the stool that extends onto the wall, mostly covered by the casing with only its end showing. For buying stock, This Old House gives the rule as the width of the window, plus the width of each casing, plus 2 in for the horns. That makes each horn the casing width plus 1 in (25 mm).
Three examples. A 1,200 mm opening with 75 mm horns needs a sill 1,350 mm long. In granite 150 mm deep and 75 mm thick that is a block of about 0.0152 m³ weighing 39 kg, and at £45 a metre it costs £60.75. On the US side, a 48 in opening with 3 in horns needs 54 in, which is 4.50 ft and $63.00 at $14 a foot; the same 6 × 3 in section in granite weighs 90 lb. And for interior trim, a window 35 1/2 in wide with 2 1/4 in casings takes horns of 3 1/4 in and a stool 42 in long.
Typical window sill wastage
Stone, cast stone and precast concrete sills are made or cut to the length you order, so there is nothing to allow and the cutting allowance starts at 0. Boards are different. A timber stool or an MDF or PVC window board is cut on site from stock lengths, and the ends are where the work is: notches round the jambs, and sometimes mitred returns to hide the end grain. The Fine Homebuilding article has the carpenter cutting his stock several inches too long for exactly that reason. Six 42 in stools come to 21 ft, and a 10% allowance makes it 23.1 ft.
A percentage only goes so far, though. Each sill has to come out of one piece, so the figure that decides the order is the stock length. Check that the longest sill fits within one length, then work out how many sills each length will yield.
What this tool does not do
It works on a plain rectangle. A real exterior sill has a sloped top, a drip groove underneath and often raised ends, so the weight shown is that of the solid block and the finished piece is a little lighter. It does not pick a profile, check that the wall or the lintel below can carry a heavy sill, or detail the flashing and damp-proofing under it. It does not know your supplier's stock lengths. And it sizes the sill only, not the window, the lining or the apron under an interior stool.
On-site considerations for a window sill
An exterior sill exists to throw water clear of the wall. The Brick Industry Association's Technical Note 36, written for US brick construction, says the top of a sill should slope away from the building by at least 15 degrees and the sill should extend at least 1 in (25 mm) beyond the face of the wall. Concrete and stone sills should also slope from the ends toward the centre, at 1/8 in per 12 in (3 mm in 300 mm), and flashing should be provided in the wall beneath. So the depth you enter has to cover the thickness of wall the sill sits on, plus that projection.
Bedding matters as much as length. The Cast Stone Institute's bulletin on job site handling and installation says only the ends of load-bearing lug sills should be set in a full bed of mortar, to prevent cracking when the wall settles later. Mind the weight as well, and plan how a 39 kg (86 lb) sill gets up to the opening before it arrives.
Codes and compliance
Building codes rarely say how long a sill must be. What they regulate is how high it sits, because a low sill is a fall risk and a high one can block an escape route. In the United States, the International Residential Code (linked as adopted in Virginia; states amend these figures) deals with both. Section R312.2.1 requires fall protection where the sill of an operable window is less than 18 in (457 mm) above the floor and more than 72 in (1,829 mm) above the ground outside. Section R310.2.3 says the bottom of an emergency escape opening must be no more than 44 in (1,118 mm) above the floor. In England, Approved Document K gives 800 mm as the guarding height at opening windows. Other countries have their own figures, so check locally before fixing a sill height. A heavy stone or concrete sill over an opening or on a cavity wall is also a load on the structure, and that is a question for a structural engineer.
Before you order
Measure the opening between the jambs at the level where the sill will sit, not higher up, since reveals are seldom parallel. Tell the supplier whether you want a lug sill or a slip sill, because the two are made differently at the ends. Give the length, the depth front to back and the thickness, and for stone or cast stone ask for a drawing to approve before it is made. For interior boards, measure the depth from the window frame to the face of the wall and add the nosing you want in front. Then ask what stock lengths are held.
Adjusting the defaults
The defaults are an opening of 1,200 mm or 48 in, horns of 75 mm or 3 in, and a section 150 × 75 mm or 6 × 3 in in natural stone. Every one can be changed. Set the horn to 0 for a slip sill. For an interior stool, use the casing width plus about 1 in. The material only affects the weight. Natural stone is taken at 2,560 kg/m³ (160 lb/ft³), the minimum ASTM C615 allows for granite. Concrete and cast stone are taken at 2,400 kg/m³ (150 lb/ft³), which is how the American Concrete Institute's Concrete Terminology defines normalweight concrete. A low-density limestone can be about 30% lighter than the granite figure, going by the classes in ASTM C568. No weight is shown for wood or PVC: a timber board is light enough not to matter and a PVC one is hollow.
Using this window sill calculator alongside other BuildMetricLab tools
The window area calculator works out the glazed area of the same openings, and the window replacement cost calculator prices the windows themselves. The door rough opening calculator does the equivalent sum for a door frame. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.
Sources & methodology
Sill length = opening width + 2 × horn. Total length to buy = sill length × number of windows × (1 + cutting allowance %). Cost = total length to buy × price per metre (metric) or per foot (US units). Weight each = sill length × depth × thickness × density, shown for natural stone at 2,560 kg/m³ (160 lb/ft³, the ASTM C615 minimum for granite) and for concrete or cast stone at 2,400 kg/m³ (150 lb/ft³, ACI's figure for normalweight concrete). It is the weight of a solid rectangular block; no weight is shown for wood or PVC. The horn is your own figure: the length built into the masonry for a lug sill, 0 for a slip sill, or the casing width plus the overhang beyond it for an interior stool or window board. The 75 mm (3 in) default and the 0% cutting allowance are our starting values, not published ones.
- Brick Industry Association: Technical Note 36, Brick Masonry Details, Sills and Soffits (15 degree slope, 1 in projection, sloping of concrete and stone sills, flashing)
- Cast Stone Institute: Technical Bulletin 37, Job Site Handling and Installation (bedding of load-bearing lug sills)
- Fine Homebuilding: Trimming Windows (the stool horn and how it is fitted)
- This Old House: How to Trim an Interior Window (stool stock = window width + both casings + 2 in for the horns)
- ASTM C615/C615M: Standard Specification for Granite Dimension Stone (minimum density 160 lb/ft³, 2,560 kg/m³)
- ASTM C568/C568M: Standard Specification for Limestone Dimension Stone (density classes from 110 lb/ft³)
- American Concrete Institute: ACI Concrete Terminology (normalweight concrete, approximately 150 lb/ft³, 2,400 kg/m³)
- UpCodes: International Residential Code 2021 (Virginia adoption), R312.2.1 window opening height and R310.2.3 emergency escape opening height
- GOV.UK: Approved Document K (England), guarding heights at opening windows
Frequently asked questions
Are window sill calculator results accurate enough to order materials?
For the length, yes, as long as the opening width and the horn are right: the sum is simply the width plus two horns. Measure the opening at sill level and confirm with the supplier whether the sill is a lug type built into the wall or a slip type fitted between the jambs. The weight is for a solid rectangular block, so a shaped sill will weigh a little less.
What wastage percentage should I use?
None for stone, cast stone or precast concrete sills, which are made to the length ordered. For timber, MDF or PVC boards cut on site from stock lengths, 10% is a reasonable allowance for notches and mitred returns. Each sill must come out of a single piece, so check the stock length as well as the total.
Does this replace professional advice?
No. It adds up a length and a weight. It does not check that the wall or lintel can carry a heavy sill, how the sill is flashed and bedded, or whether the sill height meets your local rules on falls and escape. Ask a structural engineer about heavy sills, and your building authority about sill heights.
Can I change the unit prices?
Yes. Enter your supplier's price per metre on the metric side or per foot on the US side, and the cost is that rate times the total length to buy. The default is only a placeholder, since sill prices vary widely with the material and the section.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













