Landscaping & Outdoor
Rain Barrel Size Calculator
Rainwater from a roof in one fall of rain, and the barrels or water butts needed to hold it
Updated October 5, 2026 · Live
What this tool does
Works out how much rainwater a roof collects from one fall of rain, from the catchment area, the rainfall and a collection efficiency, then how many barrels or water butts of your chosen size hold it, how much rain fills one and what a full one weighs.
Roof area times rainfall times collection efficiency gives the water collected; dividing by the barrel size gives the barrels needed and the rain that fills one.
People also use
Formula Used
Formula Used
How the rain barrel size calculator works
A roof collects more water than it looks as though it should. One millimetre of rain on one square metre is exactly one litre, so the metric sum is roof area × rainfall × efficiency. In US units the same sum uses a conversion factor: the Texas Water Development Board's Manual on Rainwater Harvesting puts it at about 0.62 gallons for every square foot of collection surface per inch of rain (0.623 to three places). The calculator works in either system and shows the answer in litres and US gallons.
It then turns that volume into something you can buy. Enter the size of the barrel you have in mind and it tells you how many it would take to hold the whole fall, how much rain fills one of them, how much would overflow if you fitted only one, and what the water in a full barrel weighs. That second figure is usually the surprise. A barrel on a house downpipe is full long before the storm is over.
With the US defaults, 320 ft² of roof and 1 in of rain at 85% efficiency give 320 × 1 × 0.623 × 0.85 = 170 gallons, about 642 litres. That is four 55-gallon barrels, and a single one is full after 0.32 in of rain, with about 115 gallons going to the overflow. With the metric defaults, 30 m² and 25 mm at 85% give 638 litres (168 US gallons), which is three 240-litre water butts. One butt fills after 9.4 mm.
Typical rainwater collection losses
Not all the rain that lands on the roof reaches the barrel. The Texas manual lists where it goes: the first flush that is diverted to rinse the roof, evaporation, splash-out and overshoot from the gutters in hard rain, and leaks. Rough roof surfaces hold more water back than smooth ones. For planning, it says most installers assume an efficiency of 75% to 90%, and its own worked example uses 85%, which is the default here.
Use the lower end for a rough or mossy roof, gutters that overshoot, or a system with a first-flush diverter, and the upper end for clean metal sheeting with well-kept gutters. On the default roofs, the gap between 75% and 90% is 150 against 180 gallons, or 563 against 675 litres. On the US default that moves the answer from three 55-gallon barrels to four; on the metric one it stays at three butts.
What this tool does not do
It sizes storage for one fall of rain. It does not know how much rain you get in a year, how long your dry spells last or how much water your garden uses, and those three decide how much storage is worth having. It does not design the gutters, the diverter or the overflow. It assumes the barrel is empty when the rain starts, which after a wet week it will not be. And it says nothing about water quality.
On-site considerations for rain barrel size
Measure the right area. The catchment is the roof's footprint on the ground, not the sloping surface: the Texas manual defines it as the area covered by the roof whatever its pitch, and adds that if only one side of a building is guttered, only the area drained by that gutter counts. For a barrel on one downpipe, enter the part of the roof that drains to that pipe.
Then think about weight. Water weighs one kilogram a litre, or 8.34 lb a US gallon, so a full 55-gallon barrel holds 459 lb of water and a 240-litre butt holds 240 kg. The Royal Horticultural Society's advice on collecting rainwater says to place water butts on firm, level stands, to fit a filter to keep leaves out and a close-fitting lid to discourage algae, and to join several butts together with connector kits where one is not enough. It calls 240 litres a standard UK size. The Texas manual wants tanks opaque to inhibit algae, and covered with their vents screened so that mosquitoes cannot breed.
Codes and compliance
Rules on collecting rainwater differ from place to place, and they can cover whether you may collect it at all, where the overflow goes and whether the system may connect to household plumbing. Ask your water supplier or local authority before installing anything bigger than a garden barrel. Two points hold almost everywhere. The overflow should run to a garden bed, a soakaway or a dry well, away from the foundations, and not into a foul or sanitary sewer. And barrel water is not drinking water. The US Environmental Protection Agency's page on rain barrels notes that rain running over a roof can pick up bacteria from birds and other animals and chemicals from the roofing, which is worth weighing before you use it on food crops. That page is no longer updated, but the point stands.
Before you order
Check three things against the result. First the rain that fills one barrel: if it is a small figure, most of every decent shower will pass straight to the overflow, and a second or third barrel linked to the first would catch more of it. Then the space and the base, because a row of full barrels is heavy and needs to stand level. Last, the fittings. A barrel needs a diverter to suit your downpipe, a tap high enough to get a watering can under, an overflow outlet and, if you are linking several, the connectors. Confirm the barrel's real capacity as well, since the size on the label is not always the usable volume.
Adjusting the defaults
The rainfall figure is yours to choose. The defaults, 1 in and 25 mm, are a good soaking; halve them to see what an ordinary shower gives. The RHS page offers a sense of scale for a whole year: in dry south-east England a small shed roof can collect 2,500 to 3,500 litres, enough to fill a 240-litre butt 10 to 15 times. Barrel size starts at 55 US gallons (208 litres) on the US side and 240 litres (63 US gallons) on the metric side, and the efficiency at 85%. Change any of them and the result updates.
Using this rain barrel size calculator alongside other BuildMetricLab tools
The roof area calculator helps with the catchment, though the figure needed here is the plan area and not the slope area. The gutter calculator covers the gutters and downpipes that feed the barrel, and the drip irrigation calculator sizes the drip line and emitters a barrel can feed. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.
Sources & methodology
Rainwater collected = catchment area × rainfall depth × collection efficiency. In metric units 1 mm of rain on 1 m² is 1 litre; in US units the factor is 0.623 gallons per ft² per inch (the Texas Water Development Board manual rounds it to 0.62). Barrels to hold it = collected volume ÷ barrel size, rounded up. Rain that fills one barrel = barrel size ÷ (catchment area × efficiency). Overflow from one barrel = collected volume − barrel size, never less than zero, assuming the barrel starts empty. Water weight in a full barrel = 1 kg per litre (8.34 lb per US gallon); the barrel itself is extra. 1 US gallon = 3.785 litres. The 85% efficiency default is the figure in the manual's worked example, within the 75 to 90% it says installers assume. Barrel size defaults to 55 US gallons or 240 litres and is your own figure.
- Texas Water Development Board: The Texas Manual on Rainwater Harvesting, 3rd edition (0.62 gal per ft² per inch; efficiency 75 to 90%; roof footprint as catchment; tank weight, covers and screens)
- Royal Horticultural Society (UK): Water, collecting, storing and using (standard 240 litre water butt; stands, lids, filters and linking butts)
- US Environmental Protection Agency: Soak Up the Rain, Rain Barrels (uses, and what roof runoff can pick up)
Frequently asked questions
Are rain barrel size calculator results accurate enough to order materials?
For choosing a barrel, yes. The volume is roof area times rainfall times efficiency, and the only uncertain part is the efficiency, which the Texas Water Development Board puts at 75% to 90% in practice. Measure the plan area of roof that drains to the downpipe you are using, and check the barrel's real capacity with the supplier.
What collection efficiency should I use?
85% is the default, and it is the figure the Texas Water Development Board's manual uses in its own worked example. The manual says most installers assume 75% to 90%, with water lost to first flush, evaporation, gutter splash-out and leaks. Use the lower end for a rough or mossy roof or a system with a first-flush diverter, and the upper end for clean metal sheeting.
Does this replace professional advice?
No. It works out a volume of water. It does not design the gutters, diverter or overflow, check the base under a heavy barrel, or tell you what your local rules allow. Barrel water is not drinking water. For anything connected to household plumbing or drainage, use a qualified plumber and check with your local authority.
Can I adjust the design storm rainfall figure?
Yes. The rainfall input starts at 1 in (25 mm), which is a heavy fall, and steps through depths from 0.1 to 10 in on the US side or 1 to 250 mm on the metric side. Enter the depth of the storm in question, from your own rain gauge or local weather records.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













