BuildMetricLab

Project Cost Estimators

Stucco / Siding Cost Calculator

Estimates exterior stucco or siding cost

Updated May 13, 2026 · Live

What this tool does

Estimates exterior stucco or siding cost. Hardie, vinyl, stucco, wood.

Estimates total stucco / siding cost from the area, build rate, and contingency you enter.

Inputs
ft²
$
%
%
Result

Stucco / Siding (incl. contingency)

$7,946.40

Area
860.0 ft²
Build Rate
$8.40/ft²
Base Cost
$7,224.00
Contingency @ 10%
$722.40
Planning Note
Figure assumes straightforward access; complex site conditions can add roughly 15–30%
Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
C=A⋅r⋅(1+g100)(1+t)C = A \cdot r \cdot \left(1 + \frac{g}{100}\right)(1 + t)
CC
External rendering cost
AA
Render area
rr
Build rate per ft² (editable)
gg
Contingency percentage
tt
Sales tax rate (editable)

How the stucco / siding cost calculator works

The formula is total = wall area × rate per ft² × (1 + contingency ÷ 100) × (1 + sales tax ÷ 100). With the defaults, 860 ft² (79.9 m²) at $8.40 a ft² ($90.4 a m²) is $7,224.00. A 10% contingency adds $722.40, so the total is $7,946.40, or $9.24 a ft². The default tax is 0%. At 6% sales tax the total is 7,946.40 × 1.06 = $8,423.18. The budget and premium examples in the tooltip, $4.60 and $14.00 a ft², give $4,351.60 and $13,244.00 with the same 10% contingency.

To find the wall area, multiply the perimeter by the wall height and subtract the openings. A house with an 86 ft (26.2 m) perimeter and 10 ft (3.05 m) walls has 86 × 10 = 860 ft² before openings. A window of 3 × 4 ft takes off 12 ft², and a door of 3 × 7 ft takes off 21 ft². Add gables, which are half the width times the rise: a 24 ft wide gable that rises 8 ft is 96 ft² (8.9 m²).

What the build rate covers

The rate is a single all-in price per square foot. It should include the labor, materials, scaffolding, preparation, the finish coat or paint, the contractor's overhead and margin, and clean-up. Stucco (cement plaster) is applied in coats over lath or a masonry base and cured, so it takes longer than hanging boards. Siding such as vinyl, fiber cement or wood is a very different price per square foot, and so is the finish you choose. Because one rate covers all of these, the result is only as good as the quote you take the rate from.

What this tool does not do

It does not price anything separately. It does not add the cost of removing old siding, repairing the sheathing or the framing underneath, new windows and trim, flashing, a weather-resistive barrier, insulation, paint or a second coat of color. It does not check structure, moisture or code compliance. The Planning Note it shows (that complex site conditions can add roughly 15–30%) is a shared general warning, not a calculated figure. Use the siding calculator for a board count and the paint calculator for the finish.

On-site considerations for stucco / siding cost

Work at height needs scaffolding or a safe platform; in the United States see OSHA fall-protection rules, and in Great Britain see HSE work at height. Wet cement is caustic, so wear gloves, eye protection and long sleeves; HSE cement guidance explains the burns and dermatitis it can cause. Mixing and cutting cement-based products makes silica dust (OSHA silica guidance). Old siding can hide hazards: in the US, houses built before 1978 may have lead paint, so contractors follow the EPA Renovation, Repair and Painting rule, and some older boards contain asbestos, so have them tested before removal (HSE asbestos guidance).

Codes and compliance

In the United States, the International Residential Code, Chapter 7 (ICC), covers exterior wall coverings, including a weather-resistive barrier and flashing behind stucco and siding, as adopted by your state or city. Permits are usually needed for re-siding and stucco, and fees are separate from the build cost. Stucco needs correct flashing and drainage details, because trapped water is the main cause of failure, and the Portland Cement Association publishes information on cement-based plaster. Outside the US, use your own national and local rules.

Before you order

Get at least three written, itemised quotes. Ask each contractor what the rate includes (scaffold, preparation, number of coats, finish, repairs, disposal), how many square feet they measured, and what happens if rotten sheathing is found. Compare quotes on the same specification, because a stucco quote and a vinyl siding quote are not like for like. Ask for the manufacturer's warranty and the installer's own warranty in writing, and check licensing and insurance. Break the budget into hard cost, soft cost (design, permits) and a separate contingency.

Adjusting the defaults

Every input can be changed. Replace the $8.40 rate with the figure from your quote, set the contingency to suit the condition of the wall, and enter your local sales tax if it applies. Contingency can be zero but not blank, and the tax field cannot be blank either, so the total is never based on a hidden default. The default rate is a placeholder, not a market figure.

Using this stucco / siding cost calculator alongside other BuildMetricLab tools

Pair the result with the roof replacement cost calculator when you are doing the whole exterior, and the paint calculator for finishes. Everything runs in your browser, nothing is sent anywhere, and the formula is shown so you can check the math. Conversions follow NIST SP 811.

Sources & methodology

Total = wall area × rate × (1 + contingency ÷ 100) × (1 + sales tax ÷ 100), with tax applied to the base cost plus contingency. The rate is an all-in price per ft² (or per m² on a metric page), converted exactly (1 ft² = 0.09290304 m²). The tier examples in the tooltip ($4.60, $8.40, $14.00 per ft²) are planning examples, not published statistics. Area and rate must be above zero; contingency and tax must be filled in, contingency cannot be negative, and a negative tax is treated as none. The tool does not price removal, repairs, trim, flashing, insulation or paint separately, and the Planning Note about site conditions is a general warning, not a calculated figure.

Frequently asked questions

Are stucco / siding cost calculator results accurate enough to budget a project?

They are as accurate as the rate you enter. The tool multiplies the wall area by your all-in rate, adds contingency and tax, and does nothing else. Use it to compare options, then get written quotes. The default rate is a planning example only.

What build rate should I enter?

Enter the all-in price per square foot from a quote, covering labor, materials, scaffold and margin. The tooltip gives budget, mid and premium examples of $4.60, $8.40 and $14.00 per ft² to bracket a range; they are examples, not statistics. Contingency is a separate input on top of the rate.

Does this replace professional advice?

No. This tool is a planning estimator. Stucco and siding need correct flashing, drainage and fastening, and local codes vary. For work that affects structure, moisture or code compliance, consult a licensed contractor or your local building department.

Can I change the unit prices?

Yes. The rate, contingency and tax are all editable. Enter the figures from your quote to get a total that matches your project.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.