BuildMetricLab

Drainage & Earthworks

Crushed Stone Base Calculator

Calculates crushed stone or gravel base material for paver, driveway, or shed pads

Updated May 13, 2026 · Live

What this tool does

Estimates the weight, volume and cost of compacted crushed stone or gravel base for a paver patio, driveway or shed pad.

Estimates cubic yards, tons, and material cost for a crushed stone or gravel base layer from area and depth inputs.

Inputs
ft²
lb/ft³
in
$
Result

Compacted Base Required

12.50 tons

Volume
7.41 yd³
Compacted Density
125 lb/ft³
Estimated Cost
$475.00
Spec Note
ASTM D2940 graded aggregate base (e.g. state DOT Class 5)
Price it on PlainEstimate

Opens these materials as a new estimate on PlainEstimate, our free estimate and invoice app.

Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
W=A×d×ρW = A \times d \times \rho
WW
Weight of base material required
AA
Surface area
dd
Compacted depth
ρ\rho
Compacted density

How the crushed stone base calculator works

The calculator treats the base as a flat slab of compacted stone. It multiplies the area by the depth to get a volume, then multiplies by the compacted density to get a weight. Suppliers sell crushed stone by weight, so the result is the amount to order, and the cost is that weight times your price per ton or tonne.

The formula is W = A × d × ρ, where A is the area, d the compacted depth and ρ the compacted density. Worked example, US units: 400 ft² at 6 in deep is 400 × 0.5 = 200 ft³, or 7.41 yd³. At 125 lb/ft³ that is 25,000 lb, which is 12.5 short tons. At $38 per ton the cost is $475. Worked example, metric: 40 m² at 150 mm is 40 × 0.15 = 6.0 m³, and at 2.0 t/m³ that is 12.0 tonnes, or £456 at 38 per tonne.

Typical base depths and allowances

Depth is the main driver of the result, and it scales in direct proportion. Halving the 6 in (150 mm) example to 4 in (100 mm) cuts the default from 12.5 tons to 8.33 tons. Paver patios and walkways commonly use a thinner base than driveways, and soft or wet ground needs more. Your supplier or the paver manufacturer can give the depth for your ground and load.

The tool gives the weight of compacted material. Loose stone fills more space than the finished layer, and edges and uneven ground use extra, so add an allowance of your own. A planning range of 5 to 10% is common for a simple base. At 10% the default 12.5 tons becomes 13.75 tons.

Density deserves a check. A well-graded crushed stone with fines compacts to a higher density than a clean single-size stone, which leaves voids. If your supplier quotes a bulk or loose density instead of a compacted one, using it will understate the weight you need. The same area and depth can differ by 10% or more between materials, so the supplier's figure beats the default.

What this tool does not do

It does not replace a professional quote, factor regional pricing, assess the ground, or confirm that the base is thick enough for its load. It does not add the sand bed, the geotextile or the edge restraint, and it does not work out the excavation. Those need their own quantities and the advice of a qualified designer or contractor.

On-site considerations for crushed stone base

Spread the stone in layers and compact each layer, rather than one thick pass, so the base reaches its density throughout. Keep the surface sloping gently away from buildings so water drains off. Before you dig, find out where buried services run by using your local utility-locating service, and follow local rules on excavation depth and shoring. Do not guess where cables and pipes are.

A short ton is 2,000 lb, or 0.907 tonne. A tonne is 1,000 kg, or 1.102 short tons. Suppliers in different countries quote in different units, so check which one the price refers to before you compare quotes. The default US quantity of 12.5 short tons is about 11.3 tonnes.

Codes and compliance

Aggregate bases are specified by grading and strength, and the names differ by region. In the UK the common sub-base is Type 1, from the Specification for Highway Works. In the US, states use their own graded aggregate base classes. Building rules, frost depth and drainage requirements vary by place, and a base that carries a driveway, a building or a drainage path may need an engineer's design or a permit. Check with your local authority.

Before you order

Give the supplier the area, the compacted depth and the use, and ask which grade they recommend and what density they use. Ask how the load is priced, whether delivery is included, and how much extra they advise for compaction. Compare quotes in the same units. Check access too, because a large truck needs space to tip and a hard surface to stand on.

Measure the area with care. Add the lengths and widths of each section separately, and include any extra width at edges or turning areas. A 3 ft (about 1 m) wider base on each side of a 12 ft by 30 ft pad raises the area from 360 ft² to 18 × 36 = 648 ft², which is 80% more stone.

Adjusting the defaults

Every input is editable. The defaults of 400 ft² (37 m²), 6 in (150 mm), 125 lb/ft³ (2.0 t/m³) and the price are planning values only. Replace them with your own measurements and your supplier's figures and the result recalculates at once. A blank price just hides the cost row.

Using this crushed stone base calculator alongside other BuildMetricLab tools

Use the same area with the paver, driveway and gravel calculators to work out the surface layer and the base together. All BuildMetricLab tools run in your browser, so nothing you type is sent anywhere, and every formula is shown on the page so you can check the maths.

Sources & methodology

The tool converts the area and depth to metric and finds the compacted volume: volume = area × depth. Weight = volume × compacted density. In US units, 400 ft² × 6 in = 200 ft³ (7.41 yd³), and 200 ft³ × 125 lb/ft³ = 25,000 lb = 12.5 short tons (2,000 lb each). In metric, 40 m² × 0.15 m = 6.0 m³, and 6.0 m³ × 2.0 t/m³ = 12.0 tonnes. One short ton is 0.9072 tonne. Cost = weight × the price you enter per ton (US) or tonne (metric). A compacted density of 2.0 t/m³ (125 lb/ft³) is a planning value; crushed aggregate bases commonly fall between about 1.8 and 2.3 t/m³ depending on rock type, grading and moisture, so use your supplier's figure. Loose-to-compacted allowance and wastage are not included.

Frequently asked questions

Are crushed stone base calculator results accurate enough to order materials?

They are accurate for the numbers you enter, but the result is for compacted stone. Loose stone takes more volume than the finished layer, and uneven ground, trimmed edges and spillage add to it, so ask your supplier how much extra to order. For the default 400 ft² at 6 in deep, the estimate is 12.5 tons (about 11.3 tonnes).

What wastage percentage should I use?

This tool has no wastage field, so add your own allowance to the result. A common planning allowance is 5 to 10% for a simple, flat base, and more for uneven ground or hand-dug edges. On the default 12.5 tons, 10% means ordering about 13.75 tons. The supplier can advise on the extra needed to allow for compaction.

Does this replace professional advice?

No. This is a planning estimator only. Where the base supports a driveway, a structure or a drainage path, a licensed contractor or engineer should confirm the design, depth and compaction before you order materials or start work.

Can I change the unit prices?

Yes. Every field is editable, including the price per ton and the compacted density. Enter the figures from your supplier's quote. If you leave the price blank, the tool drops the cost row.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.