Landscaping & Outdoor
Pond Liner Calculator
Pond liner sheet size and cost from length, width, depth and overlap
Updated May 13, 2026 · Live
What this tool does
Estimates the size and area of pond liner for a pond from its longest length, widest width, maximum depth and an overlap at the edges, with the cost.
Estimates the length, width and area of pond liner from the pond's length, width, depth and the overlap at the edges, with the cost.
People also use
Formula Used
Formula Used
How the pond liner calculator works
A flexible pond liner is a single sheet that lines the hole, so its length and width must cover the pond's longest run, the dip down and the climb up the other side, and a margin at each edge. This calculator adds those three amounts to the pond's length and width, multiplies the two to get the area and prices it. The formula is A = (L + 2D + 2O) × (W + 2D + 2O), where D is the maximum depth and O the overlap at each edge. The page works in feet and converts internally, so the metric and US-unit versions agree.
Example with the defaults on this page: a pond 10 ft long, 6.5 ft wide and 2 ft deep with a 1 ft overlap needs a liner (10 + 2 × 2 + 2 × 1) = 16 ft long by (6.5 + 4 + 2) = 12.5 ft wide. The area is 16 × 12.5 = 200 ft², which is 18.6 m², and at $1 per ft² the cost is $200. In metric, the sheet is 4.88 m by 3.81 m.
Overlap changes the answer. With the RHS's 6 in (0.5 ft) overlap instead, the sheet is (10 + 4 + 1) × (6.5 + 4 + 1) = 15 × 11.5 = 172.5 ft². A shallow pond of 1 ft depth with the same footprint and 1 ft overlap needs (10 + 2 + 2) × (6.5 + 2 + 2) = 14 × 10.5 = 147 ft². Depth counts twice, so a deeper pond takes much more liner. As a cross-check, the University of California guide's own example, a pond 15 ft long, 10 ft wide and 2 ft deep, gives a 21 ft by 16 ft sheet, and the tool gives the same with a 1 ft overlap.
Typical US landscaping and outdoor wastage
There is no wastage percentage on a liner, because the allowance is the overlap. The RSPB's method uses the maximum length and width plus twice the maximum depth, and the RHS advises about 6 in (15 cm) of overlap all round. The tool's default of 1 ft per side is more generous, which is useful if you want to bury the edge under stones or turf. A University of California extension guide uses a different rule of thumb, adding three times the depth to both dimensions, which here gives the same answer as the default overlap.
Because liner is sold in set sizes, you will probably buy a slightly larger sheet than the exact area. Liners in the US are sold in set sizes, and some suppliers cut them to length from a roll. Check the supplier's sizes against your length and width, because a sheet that is a few inches short on one side is no use. Buying the next size up is cheaper than a joint or a leak.
What this tool does not do
It does not choose a liner type, size an underlay, or plan the excavation. It does not work out the pond's water volume, for which see the pond volume calculator, and it does not size a pump or filter. It uses the pond's bounding length and width, so for a free-form pond it errs on the generous side, and a pond with steep sides, deep shelves or an uneven floor needs extra that the formula cannot see. It prices the liner only.
On-site considerations for pond liner
Measure the longest length, the widest width and the greatest depth of the finished hole, not the surface of a sketched outline. For a free-form pond, take the length and width at their furthest points. RSPB notes that the standard calculation assumes gently sloping margins, so steep edges need more material. Dig the hole, remove stones and roots from the sides and base, and line it with sand or an underlay before you lay the liner, as the RHS advises. Fold the liner loosely into the corners without stretching it, because it needs slack to settle under the weight of the water.
Fill the pond slowly, letting the liner settle into the shape of the hole, and trim the spare after the water is in. Keep the top edge of the liner higher than the water level all round, so that water does not wick out over the edge. Plan shelves for plants and a gentle slope on one side, so that wildlife can get out.
Codes and compliance
A small garden pond does not normally need a permit. In some places a pond deeper than about 2 ft (0.6 m) is treated like a swimming pool and needs a barrier, so ask your local authority. Ponds are a drowning hazard, and the WHO's drowning fact sheet names children as the most at risk and recommends barriers and supervision. A shallow pond, a mesh cover or a fence reduces the risk. Pumps and lights near water need an electrician and protection against shock. Other countries have their own rules, so follow the ones where you build.
Before you order
Check your measurements and the depth of the finished hole. Decide on the overlap, and add the underlay, which is usually the same size or a little smaller than the liner. Compare liner types and thicknesses, such as EPDM rubber, butyl and PVC, for their lifespan and for any warranty, and check that they are fish-safe if you plan to keep fish. Ask the supplier for the stock sizes, and choose the smallest sheet that is at least as long and as wide as the tool gives. Keep the liner out of direct sun until you lay it.
Adjusting the defaults
Every input is editable. The length, width and depth must be above zero, and the overlap must be zero or more. A blank or zero length, width or depth is refused instead of silently using a default, and a blank price hides the cost line. For a pond with steep sides, increase the overlap or the depth to add margin, and follow the supplier's guidance for the liner you choose.
Using this pond liner calculator alongside other BuildMetricLab tools
Pair this estimate with the pond volume calculator for the water and the fill time, and with the topsoil, gravel and mulch calculators for the surround. All BuildMetricLab tools run in your browser. Nothing you type is sent anywhere, and every formula is shown on the page so you can audit the maths.
Sources & methodology
Each dimension of the sheet is the pond's longest run plus twice its maximum depth plus an overlap at each edge: liner length = L + 2D + 2O and liner width = W + 2D + 2O, and the area is their product. The 2D term takes the liner down one side and up the other. The page takes lengths in ft and the price per ft², and converts them (1 ft = 0.3048 m) so both unit systems agree. Cost = area × price per unit area, hidden if no price is entered. The length, width and depth must be above zero, the overlap zero or more, and the price zero or more. The formula suits a pond with gently sloping or near-vertical sides, and it uses the bounding length and width, so for an irregular pond it errs on the generous side. Steep sides, deep shelves and a gradient that is not even need extra. The tool does not size an underlay, which is bought separately, or the stones and edging that hide the liner.
- University of California Agriculture and Natural Resources — Create a garden pond for wildlife (US)
- RHS — How to make a new pond: liners, underlay and overlap (UK)
- WHO — Drowning: fact sheet on risk and prevention (international)
- NIST — Special Publication 811, Guide for the Use of the International System of Units (ft, ft² and m, m²)
Frequently asked questions
Are pond liner calculator results accurate enough to order materials?
They are a good starting size for a pond with gently sloping sides. Liner is sold in set sizes, so round up to the next size the supplier offers. The result is only as accurate as the length, width and depth you measure, and steep sides, deep shelves or an irregular outline need extra. Check the size with your supplier before you order.
How much overlap should I allow for the pond liner?
The Royal Horticultural Society gives about 6 in (15 cm) of overlap all round as a guide, and the tool defaults to 1 ft per side, which gives room to anchor the edge under stones or turf. Increase it for an irregular edge, a waterfall or extra anchoring. Reduce it only if your supplier confirms a simple edge detail. Overlap is added at both ends of each dimension.
Is this a substitute for a supplier quote or professional consultation?
No. It estimates the liner size and cost only. It does not choose a liner type, plan the excavation, size a pump or check local rules. For work near a house or services, or for large or deep ponds, ask a pond specialist or a licensed contractor.
Can I change the unit prices?
Yes. The price per ft² is editable, and a blank price hides the cost line so only the size shows. A price of zero is accepted. The length, width and depth must be above zero, and the overlap must be zero or more.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













