Flooring
Epoxy Floor Coating Calculator
Epoxy floor coating kits from the floor area, the coverage per coat on the kit label and the coats, with an allowance, a wet-film check and cost
Updated October 9, 2026 · Live
What this tool does
Works out how many epoxy floor coating kits to buy from the floor area, the per-coat coverage on the label (ft²/gal or m²/L), the number of coats and a loss allowance, rounding up to whole kits. Shows the coating in gallons and litres, what one kit covers, the wet film the rate implies, and the cost at your kit price.
Area times coats divided by the coverage per coat, plus an allowance, in whole kits.
People also use
Formula Used
Formula Used
How the epoxy floor coating calculator works
An epoxy floor is bought by the kit, and the kit label gives one figure that matters: the area it covers in one coat. The estimate is the floor area times the number of coats, divided by that coverage, plus an allowance for what stays in the roller tray and soaks into rough concrete, rounded up to whole kits. Rust-Oleum's EpoxyShield technical data (US) puts its 120 fl oz garage kit, 90 fl oz of base and 30 fl oz of activator, at "approximately 250 sq.ft./kit" in one coat, a practical figure that already "assume[s] 15% material loss"; that is 0.94 gal (3.55 L) covering 23 m², about 267 ft²/gal. The RockSolid Polycuramine sheet (US) gives 200 to 250 ft² per kit, "coverage rate can vary depending on texture and porosity of concrete", for a one-coat system at 96% solids. In the UK, Watco's Epoxy Matt Coat is listed at 30 m² per 5 L pack per coat, 6 m²/L, with two coats, and Rust-Oleum's EpoxyShield 5300 MAXX data sheet at about 7 m²/L in one coat.
The US default is a 400 ft² (37.2 m²) two-car garage at 250 ft²/gal in one coat: 1.60 gal (6.1 L) of coating, 1.76 gal (6.7 L) with a 10% allowance, so two 0.94 gal kits, $220 at $110 a kit, which is two one-car kits. The metric default is 30 m² (323 ft²) at 6 m²/L in two coats: 10.0 L (2.64 gal), 11.0 L with the allowance, so three 5 L packs at £95 is £285. On both sides the One Kit Covers row is the label figure for one coat, and the Coverage row shows the rate in both units, so a UK sheet in m²/L and a US sheet in ft²/gal can be compared: 6 m²/L is 244 ft²/gal and 250 ft²/gal is 6.1 m²/L.
Typical US flooring wastage
The allowance is separate from the coverage because the sheets treat it differently. EpoxyShield's 250 ft² is already net of a 15% loss, so for that product the allowance can be set to 0 or kept as a margin for a rough slab; RockSolid gives a range instead, 200 to 250 ft², and the lower end is the allowance. The 10% default suits a smooth, sealed-looking slab coated once; raise it for a broom-finished or ground floor that drinks the first coat, for a floor cut up by drains and columns where the roller cannot run full, or for a first attempt. Epoxy cannot be returned to the pot once mixed, so the allowance also buys the spare that an exact count would not.
The Wet Film row is a check on the rate itself. One litre spread over one square metre is a 1 mm film, so a coverage of 6 m²/L is 167 µm wet; one US gallon over one square foot is 1,604 mils, so 250 ft²/gal is 6.4 mils wet, the identity Spartan Chemical's mil thickness bulletin (US) states as "mil = solids × 1604 ÷ coverage". Compare that with the wet film on the sheet: EpoxyShield wants 6.0 to 7.0 mils wet (150 to 175 µm) for 3.0 to 3.5 mils dry at 52.6 to 52.8% solids by volume, and Watco wants 160 µm wet for 100 µm dry. A rate that gives a thinner wet film than the sheet is spreading the kit too far.
What this tool does not do
It does not include the etch or grinder rental, the primer some systems want on bare concrete, the decorative chips, or the clear top coat that is a separate kit with its own coverage; run it again for the top coat. It does not know whether the slab is sound: both US sheets exclude floors with a moisture problem, and RockSolid describes the test, a plastic sheet taped down for 24 hours with the concrete darker underneath if it is damp, and asks for new concrete to cure 30 days. It does not price labour, and it cannot say whether a coating is the right finish for a floor that gets hot-tyre pickup, chemical spills or standing water.
On-site considerations for epoxy floor coating
The kit sets the pace. EpoxyShield gives a pot life of 1.5 to 2 hours after mixing depending on temperature, with an induction wait before rolling; RockSolid gives 45 minutes to an hour. One kit is mixed and rolled out, keeping a wet edge to prevent lap marks as the EpoxyShield sheet puts it, before the next is opened. EpoxyShield applies between 60 and 85°F (15 to 29°C) air, material and surface temperature; Watco is overcoatable after 4 to 6 hours at 20°C with a pot life of up to 2 hours. RockSolid allows vehicle traffic after 24 to 36 hours depending on temperature, so a floor done in the cold waits at the long end of that.
Codes and compliance
There is no building code for a garage floor paint, but there are product rules that change the count. Water-based epoxies carry low VOC figures (EpoxyShield under 100 g/L, RockSolid under 1 g/L), and that line on the sheet is there to be checked against the local limit: architectural coatings are subject to VOC limits in parts of the United States, with California's the strictest, and to the Paints Directive limits in the EU and UK. A floor that forms part of a fire escape route or a food area has its own rules for slip resistance and hygiene, which the designer, not the kit, has to meet.
Before you order
The kits for one coat come from one batch where the colour matters, because a tinted base can drift between batches. Check that the kit size on the label matches the one you entered: EpoxyShield one-car kits are 120 fl oz, RockSolid sells one-car and 2.5-car kits, and UK packs are 5 L or 10 L. If the result is a fraction over a whole kit, the Coating Needed row shows the margin, and lowering the allowance may save a kit on a smooth floor; a kit short on a rough one cannot be made up later without a visible lap.
Adjusting the defaults
Every input is editable. Floor area is wall to wall at floor level, less nothing for a car. Coverage is the per-coat figure on the label, in ft²/gal or m²/L; where the label gives square feet per kit, divide by the kit size in gallons. Coats is what the system calls for, one for the garage kits and two for the UK water-based coats. The allowance runs from 0 to 30%, the kit size is the mixed volume of base plus activator, and the price per kit can be left at zero for quantities only.
Using this epoxy floor coating calculator alongside other BuildMetricLab tools
Level a bad slab first with the self-levelling underlayment calculator, and price a painted alternative with the painting cost calculator. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.
Sources & methodology
Coating = floor area × coats ÷ coverage per coat; with allowance = coating × (1 + allowance %); kits = that ÷ kit size, rounded up; cost = kits × price. One kit covers per coat = kit size × coverage. Wet film = 1,000 ÷ coverage in m²/L (µm) = 1,604 ÷ coverage in ft²/gal (mils). US inputs are converted first: ft² × 0.0929 to m², ft²/gal × 0.02454 to m²/L (0.0929 m² per ft² ÷ 3.785 L per gal), gal × 3.785 to L. Label figures: Rust-Oleum EpoxyShield 250 ft² per 120 fl oz kit in one coat, after 15% loss (about 267 ft²/gal, 6.5 m²/L); RockSolid 200 to 250 ft² per kit; Watco Epoxy Matt Coat 30 m² per 5 L per coat (6 m²/L), two coats; Rust-Oleum EpoxyShield 5300 MAXX about 7 m²/L, one coat.
- Rust-Oleum, EpoxyShield Water-Based Epoxy Garage Floor Coating technical data ESH-09 (US): kit 90 + 30 fl oz, practical coverage about 250 sq ft per kit assuming 15% loss, 3.0 to 3.5 mils dry from 6.0 to 7.0 mils wet, 52.6 to 52.8% solids by volume, pot life 1.5 to 2 hours, apply at 60 to 85°F
- Rust-Oleum, RockSolid Garage Floor Coating Kit technical data RSD-10 (US): 96% solids, practical coverage 200 to 250 sq ft per kit varying with porosity, pot life 45 minutes to 1 hour, one coat, moisture test and 30-day cure for new concrete
- Promain, Watco Epoxy Matt Coat (UK): 30 m² per 5 L per coat, 160 µm wet and 100 µm dry film, pot life up to 2 hours at 20°C, overcoatable in 4 to 6 hours
- Rust-Oleum Netherlands, EpoxyShield 5300 MAXX product data sheet (UK/EU): coverage approx. 7 m²/L, one coat generally sufficient
- Spartan Chemical, Mil Thickness bulletin (US): mil = solids × 1604 ÷ coverage in sq ft per gal, where 1604 is the film from one gallon of 100% solids on one square foot
Frequently asked questions
Are epoxy floor coating calculator results accurate enough to order materials?
Yes, if the coverage is the per-coat figure on your kit's label and the allowance suits the slab. The count rounds up to whole kits, and the Coating Needed row shows how close the call is. On a rough or porous floor the label's lower figure is the one to use, and a kit short cannot be made up later without a visible lap.
How many coats should I plan for?
What the product's sheet calls for. The US garage kits (Rust-Oleum EpoxyShield, RockSolid) are one-coat systems at their stated coverage; Watco's UK water-based epoxy is applied in two coats at 30 m² per 5 L pack each. A clear top coat is a separate product with its own coverage, so run the calculator again for it rather than adding a coat here. Each coat added multiplies the volume and the kit count.
Does this replace professional advice?
No. It counts kits. Whether the slab is dry enough to coat, whether it needs grinding or etching, and whether a coating suits the use are matters for the product's data sheet and an installer. For work that affects structure, gas, electrics, plumbing or drainage to a public sewer, use a suitably qualified professional.
Can I change the unit prices?
Yes. The price per kit is an input, so enter what your supplier charges for the kit size you entered, and the cost is that price times the whole kits needed. Leave it at zero to see quantities only.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













