BuildMetricLab

Surveying & Mapping

Bearing and Distance Calculator

Grid distance, whole-circle and quadrant bearing between two easting and northing points

Updated October 1, 2026 · Live

What this tool does

Gives the straight-line grid distance between two points entered as eastings and northings, the bearing from the first to the second as decimal degrees, degrees-minutes-seconds and a quadrant bearing, the back bearing, and the change in easting and northing.

Pythagoras on the easting and northing differences for the distance; the two-argument arctangent, clockwise from grid north, for the bearing.

Inputs
ft
ft
ft
ft
Result

Grid Distance Between Points

466.69 ft

Whole-Circle Bearing (grid azimuth)
45.0000°
Bearing (DMS)
45° 00' 00.0"
Quadrant Bearing
N 45° 00' 00.0" E
Back Bearing (2 to 1)
225.0000° (225° 00' 00.0")
Easting Change (ΔE)
330.00 ft
Northing Change (ΔN)
330.00 ft
Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
D=(E2−E1)2+(N2−N1)2θ=atan2⁡(E2−E1,  N2−N1) mod 360∘\begin{aligned} D &= \sqrt{(E_2 - E_1)^2 + (N_2 - N_1)^2} \\ \theta &= \operatorname{atan2}(E_2 - E_1,\; N_2 - N_1) \bmod 360^{\circ} \end{aligned}
DD
Grid distance (ft)
θ\theta
Whole-circle bearing, clockwise from grid north
E1E_1
Easting of point 1
N1N_1
Northing of point 1
E2E_2
Easting of point 2
N2N_2
Northing of point 2

How the bearing and distance calculator works

Give it two points as grid coordinates, an easting and a northing each, and it returns the straight-line distance between them and the direction from the first to the second. The distance is Pythagoras on the two differences. The bearing is the angle clockwise from grid north, the direction the northing axis points, worked out with the two-argument arctangent so it lands in the right quadrant whatever the signs of the differences. It comes out three ways. The whole-circle bearing in decimal degrees is the grid azimuth in American usage. The same angle is shown in degrees, minutes and seconds, and the quadrant bearing is the form written on American plats and older deeds, N 38° 39' 35" W. The back bearing, from the second point to the first, is the same angle plus or minus 180°.

The defaults are a point at the origin and a point 100 m east and 100 m north of it, or 330 ft and 330 ft with US units. The distance is √(100² + 100²) = 141.42 m, or √(330² + 330²) = 466.69 ft, and the bearing is 45°, N 45° E. A less tidy pair shows the quadrant logic. From easting 500, northing 200 to easting 380, northing 350, all in metres, the easting falls by 120 and the northing rises by 150, so the distance is √(120² + 150²) = 192.09 m and the direction is north-west. The whole-circle bearing is 360° − arctan(120 ÷ 150) = 321.3402°, which is 321° 20' 24.7", or N 38° 39' 35.3" W as a quadrant bearing; the back bearing is 141.3402°.

Which coordinates to enter

The inputs are plane grid coordinates, not latitude and longitude. In Britain that is the National Grid, eastings and northings in metres. In the US it is a State Plane zone, usually in US survey feet, or a site grid. Australia uses MGA2020 zones; Canada uses UTM, with 3° MTM zones in Ontario, Quebec and the Maritimes; most of the rest of the world uses UTM. All of these are flat projections of a curved surface, so Pythagoras is the right arithmetic on them and the results are grid distances and grid bearings. Both points must be in the same system and the same zone, and in the same units as the page. A pair of GPS latitudes and longitudes entered here will give nonsense, because degrees of latitude and longitude are not the same length and are not Cartesian; convert them to a grid first.

Enter the full coordinates or the local ones, it makes no difference, because only the differences are used. Ordnance Survey eastings run to six figures and State Plane to seven; typing 451234.56 and 451334.56 gives the same answer as 0 and 100. A lettered grid reference such as SE 12345 67890 has to go in as the full numeric easting and northing, 412345 and 467890, because the letters stand for a 100 km square. In Britain the coordinates come from a topographical survey, OS MasterMap or a GNSS fix in OSGB36, not from a title plan, which shows general boundaries at 1:1,250 without coordinates or dimensions.

Grid distance and ground distance

A grid distance is slightly different from what a tape or a total station reads on the ground, because a projection cannot show a curved surface at true scale everywhere. The Ordnance Survey guide to coordinate systems explains that the National Grid's Transverse Mercator projection has a central meridian scale factor of about 0.9996 at 2° west. Its two lines of true scale lie about 180 km east and west of that meridian. Between them the grid is slightly smaller than the ground, outside them slightly larger. The effect is small, 100 m of grid at the central meridian being 100.04 m on the ground, and for a site plan it is ignored. Where it matters, a surveyor applies the local scale factor and an elevation factor. Grid north is not true north either. The two differ by the grid convergence, which is zero on the central meridian and grows to a few degrees at the edges of a zone, and compass readings differ again by the magnetic declination. The bearing here is a grid bearing.

State Plane zones were laid out to a design limit of one part in ten thousand of scale error, which some single-zone states now exceed by choice. The National Geodetic Survey's State Plane pages give the zone definitions and the tools to convert between systems. Zones defined in US survey feet and in international feet differ by two parts per million, which is 2 ft over 1,000,000 ft and matters only on long lines or when mixing sources.

Reading the bearing

A whole-circle bearing runs 0° to 360° clockwise from north: 0° north, 90° east, 180° south, 270° west. A quadrant bearing gives the acute angle from north or south towards east or west, so 321.34° becomes N 38.66° W and 135° becomes S 45° E. Legal descriptions in the US mostly use quadrant bearings, as do Ontario deeds and plans; Quebec and the western provinces lean to azimuths; British and Australian survey plans use whole-circle bearings. All describe the same line. To walk the line in the other direction, use the back bearing. Two points on the same easting give due north or due south; on the same northing, due east or due west. The calculator works one way only, from coordinates to bearing and distance; it does not plot the next corner from a deed's bearing and distance. A deed's bearings are on whatever basis it states, magnetic, astronomic or grid, so check that basis before comparing them with a grid bearing from here.

What the result is not

It is not a legal boundary, a measured survey or a geodetic distance. Boundary lines come from the deed or title plan and the monuments on the ground, read by a licensed, registered or chartered surveyor. A calculation from coordinates typed off a plan is only as good as those coordinates and the scale of the plan. For distances across a county or a country, or between latitude and longitude pairs, use a geodesic calculation rather than this one. The area from coordinates calculator uses the same grid coordinates to give the area of a plot.

Using this with other BuildMetricLab tools

Run the bearings round a plot one line at a time to check a surveyed plan's lines. The area from coordinates calculator then does the whole plot, and the two should agree with the plan's area. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.

Sources & methodology

Distance = √((E2 − E1)² + (N2 − N1)²). Whole-circle bearing = atan2(E2 − E1, N2 − N1), clockwise from grid north, in the range 0° to 360°; shown as decimal degrees, as degrees, minutes and seconds to 0.1", and as a quadrant bearing. Back bearing = bearing + 180° (mod 360°). Coordinates are taken as metres on the metric side and feet on the US-units side; the results are grid, not ground, figures.

Frequently asked questions

Are bearing and distance calculator results accurate enough for a legal survey?

No. It does plane geometry on the coordinates you type, so it is exactly right for those coordinates and says nothing about where the boundary is on the ground. For boundary determination, legal descriptions or any document that needs certifying, use a licensed, registered or chartered land surveyor.

What coordinate system does this calculator assume?

Any flat grid with an easting and a northing: the British National Grid, a US State Plane zone, an MGA, MTM or UTM zone, or a site grid. Both points go in the same system and zone, in the page's unit. What comes out is a grid figure, which a surveyor corrects to ground distance and true bearing.

Can I use latitude and longitude GPS coordinates directly?

No. Latitude and longitude are angles on a curved surface, so Pythagoras on them gives the wrong answer. Convert them to grid coordinates first, or use a geodesic formula such as Vincenty or the haversine for a distance over the curve of the Earth.

Does this replace a licensed surveyor?

No. It checks the arithmetic between two points. Setting out a building, fixing a boundary or signing a plan is work for a surveyor, who also applies the scale factor that turns a grid distance into a ground one and the convergence that turns a grid bearing into a true one.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.