Swimming Pool
Pool Volume Calculator
Pool water volume in gallons and litres from length, width and depths
Updated May 13, 2026 · Live
What this tool does
Estimates the water volume of a swimming pool in US gallons, litres and cubic metres from its length, width and shallow-end and deep-end depths.
Estimates the water volume of a swimming pool from its length, width and the average of the shallow-end and deep-end depths.
People also use
Formula Used
Formula Used
How the pool volume calculator works
The volume of a pool is its length times its width times its average depth. Most pools slope from a shallow end to a deep end, so the calculator averages the two depths. The formula is V = L × W × (d_s + d_d) ÷ 2. It then converts the cubic metres to US gallons and litres. The page works in feet and converts internally, so the metric and US-unit versions of the same pool agree.
Example with the defaults on this page: a pool 26 ft long and 13 ft wide with a 4 ft shallow end and a 6.5 ft deep end has an average depth of (4 + 6.5) ÷ 2 = 5.25 ft. The volume is 26 × 13 × 5.25 = 1,774.5 ft³, and at 7.4805 gallons per cubic foot that is 13,274 US gallons, which is 50.25 m³ or 50,248 litres. The water weighs about 110,700 lb, or 50 tonnes.
The same pool as an oval has a footprint of π ÷ 4 = 0.785 of the bounding rectangle, so the volume is 13,274 × 0.785 = 10,425 gallons. A small plunge pool that is 10 ft by 6 ft with an even depth of 4 ft holds 10 × 6 × 4 = 240 ft³, which is 1,795 gallons. In metric, a pool 8 m by 4 m with depths of 1.2 and 2 m holds 8 × 4 × 1.6 = 51.2 m³, or 51,200 L.
Typical US swimming pool wastage
There is no wastage on a volume, so the question is accuracy. The simple average is exact only for a pool whose floor slopes evenly. A pool with a flat shallow shelf, a slope and a flat deep end has a different average depth, because the deep end counts for more or less depending on how long it is. For such a pool, split it into sections, work out each volume and add them. Rounded corners, steps, a bench and a hopper or pit at the deep end all change the true volume by a few percent.
Accuracy matters for chemicals. A 5% error in volume gives a 5% error in a dose, so a pool that is bigger than you think can be under-treated. The best check is to compare the tool with the builder's plans or the volume stated on the pool equipment, and to test the water and adjust, because the water test is what decides the dose.
What this tool does not do
It does not size a pump, filter or heater, set the chemical dose, or advise on water balance. It assumes a rectangular footprint, so for an oval or a kidney shape it overestimates, and you should multiply the result by about 0.785 for an oval and 0.8 to 0.9 for a free-form pool. It does not subtract steps, a swim-out or a bench. It does not include the water in a spa that shares the circulation, or in the pipes and equipment.
On-site considerations for pool volume
Measure the length and width at the waterline, because the water surface sits below the coping or tiles. Measure the depth from the water surface down, at the shallow end and at the deepest point, with a weighted tape. A pool that is full to the middle of the tile band is the right level, and a pool that is low reads shallow. Check your measurements twice, because an error of 100 mm (4 in) in depth on a 1.6 m (5.25 ft) average is 6%.
The volume feeds many pool jobs. Heating one cubic metre of water by one degree Celsius takes about 1.16 kWh, so heating the 51.2 m³ example by 1 °C needs about 60 kWh. In US units, it takes about 1 BTU to raise a pound of water by 1 °F, so 110,700 lb needs about 110,700 BTU per °F. Pump turnover, filter sizing and the time to fill from a tap all depend on the same figure.
Codes and compliance
In the United States, state and local codes set pool barrier and water quality rules, and the Pool and Hot Tub Alliance publishes industry standards. A pool is a drowning hazard, and the WHO's drowning fact sheet names children as the most at risk and recommends barriers, supervision and swimming lessons. Many places require a fence or barrier around a pool and may treat an outdoor pool as a structure that needs a permit and inspection, so check before you build or fill one. Electrical equipment near water needs a qualified electrician and protective devices. Pool chemicals are hazardous: follow the label, store them dry and apart, and never mix different chlorine products.
Before you order
Confirm the volume with your builder's plans, and use it for chemicals, heating and pump sizing. For a chlorine dose, remember that the row in the tool is an example: it shows the available chlorine to raise the water by 2 ppm, which is 2 g per cubic metre, and operators commonly keep free chlorine within a range of a few ppm that depends on the stabiliser, the pool's use and local rules. Test the water with a kit, add chemicals in the amounts the label gives for your volume, and retest after the water has circulated. Compare the price per gallon of treated water, not just the price of the product.
Adjusting the defaults
Every input is editable. The length, width and both depths must be above zero. A blank or zero field is refused instead of silently using a default. For a pool of even depth, enter the same value for both depths. For an oval or kidney-shaped pool, enter the longest length and the widest width, and multiply the result by a shape factor of about 0.785 for an oval or 0.8 to 0.9 for a free-form shape.
Using this pool volume calculator alongside other BuildMetricLab tools
Pair this estimate with the pool liner and pool tile calculators to cost the build, and with the pool concrete calculator for the shell. All BuildMetricLab tools run in your browser. Nothing you type is sent anywhere, and every formula is shown on the page so you can audit the maths.
Sources & methodology
Volume = length × width × (shallow depth + deep depth) ÷ 2. The page takes lengths in ft and converts them (1 ft = 0.3048 m), and gives litres and gallons from the cubic metres (1 m³ = 1,000 L = 264.172 US gal = 219.969 UK gal; 1 ft³ = 7.4805 US gal). The chlorine row is a dose to raise the available chlorine in the water by 2 mg/L (2 ppm), which is 2 g per m³, and it is only an example of a dose, not a target. The length, width and both depths must be above zero. The average-depth method is exact for a pool whose floor slopes evenly between two depths; a flat shelf, a deep pit or a bench changes the true volume. A rectangular formula overestimates an oval or kidney-shaped pool, so multiply by about 0.785 for an oval, and the result is an upper bound for other shapes. The tool measures to the waterline, so measure depth from the water surface and not from the coping.
- WHO — Guidelines for safe recreational water environments, Volume 2: swimming pools and similar environments
- PHTA — Pool & Hot Tub Alliance: standards and resources (US)
- WHO — Drowning: fact sheet on risk and prevention
- NIST — Special Publication 811, Guide for the Use of the International System of Units (ft³, gal and m³)
Frequently asked questions
Are pool volume calculator results accurate enough to order materials?
They are a good planning figure for a rectangular pool that slopes evenly. The volume is only as good as your measurements, and the real shape can differ. For chemicals, a 5% error in volume gives a 5% error in dose, so confirm the volume with the pool builder's plans for a large or unusual pool, and test the water to adjust.
Why do I need both a shallow-end and deep-end depth?
Most pools are not an even depth. They slope from a shallow end to a deep end. The calculator uses the average of the two depths, which is exact for a pool that slopes evenly. If your pool has an even depth, enter the same value in both fields. If it has a flat shallow shelf, a slope and then a flat deep end, the average depth depends on how long each section is, and the simple average can be wrong.
Is this a substitute for a pool professional?
No. It estimates water volume only. It does not size equipment, set chemical doses for you or check the pool's safety or code compliance. For electrical work, plumbing or structural work, and for water quality advice, consult a licensed pool professional.
Can I use this for oval or kidney-shaped pools?
Only as an upper bound. Enter the longest length, widest width and the two depths, then multiply the result by a shape factor: about 0.785 for a true oval or circle (π ÷ 4), and roughly 0.8 to 0.9 for a kidney or free-form shape. For the default pool that gives about 10,425 gal as an oval, against 13,274 gal for the full rectangle. Check against your builder's plans for a precise figure.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













