Renewables
EV Charging Cost & Time Calculator
Work out charge time and cost from current to target charge
Updated July 12, 2026 · Live
What this tool does
Works out how long an EV takes to charge and what it costs from the current charge level to a target, at a given charger power and electricity price.
Enter the battery size, current and target charge, charger power and electricity price; the calculator returns the charge time and cost.
People also use
Formula Used
Formula Used
How the ev charging cost & time works
The calculator finds the energy added to the battery, then the time and the cost. Energy is the battery capacity times the gap between current and target charge: E = C × (t − s) ÷ 100, where C is the usable capacity in kWh and s and t are the starting and target charge in percent. Time is E ÷ P, where P is the charger power in kW. Cost is E × p, where p is your price per kWh. The result is shown in hours and minutes, rounded to the nearest minute.
Worked example with the defaults: a 60 kWh battery charged from 20% to 80% adds 60 × 0.6 = 36 kWh. At 7 kW that takes 36 ÷ 7 = 5.14 h, which is 5 h 9 min (0.143 h × 60 = 8.6 min, rounded up to 9). At a price of 0.27 per kWh the cost is 36 × 0.27 = 9.72. A full charge of a 75 kWh battery from 0% to 100% at 11 kW takes 75 ÷ 11 = 6.82 h, or 6 h 49 min, and at 0.30 per kWh costs 22.50. A rapid session of 42 kWh (60 kWh from 10% to 80%) at 50 kW is 42 ÷ 50 = 0.84 h, about 50 minutes, and at 0.55 per kWh costs 23.10.
What you enter
Enter the usable battery capacity in kWh. This is the figure in the vehicle specification and is often a little lower than the headline gross capacity. Then enter the current and target charge in percent, the charger power in kW and your electricity price per kWh in your own currency. The tool uses kWh, kW and percent, so it works the same in metric and US units and the price is only a label. Every field is editable and the result updates as you type.
The charger power is the lower of two limits: the charger's output and the most the car can accept. A 22 kW public AC point charging a car with a 7 kW onboard charger delivers 7 kW. The US Department of Energy's Alternative Fuels Data Center describes three common levels: Level 1 on a standard household outlet (about 1.9 kW on a 120 V circuit, around 5 miles or 8 km of range per hour), Level 2 on a 240 V circuit, and DC fast charging. Many other countries use single-phase or three-phase AC wallboxes at 3.7 to 22 kW instead.
Reading the result
The time and cost are a best case at steady power. Real sessions are slower, because the car reduces the charge rate as the battery fills (commonly above about 80%), in cold weather and when the battery is hot. For that reason, treat the time as a minimum. Rapid chargers show this most. A 50 kW rapid charger rarely holds 50 kW for the whole session.
The cost is the energy added to the battery times your price. The energy drawn from the socket is a little higher, because the charger and the battery lose some energy as heat, so your meter or bill will show slightly more than the figure here. Public chargers may also add a session or idle fee, which the tool does not include.
To compare tariffs, change only the price. The same 36 kWh costs 36 × 0.09 = 3.24 at a cheap overnight price of 0.09 per kWh and 9.72 at 0.27 per kWh. To see how long a plug-in on a standard household outlet takes, enter 1.9 kW: the same 36 kWh needs 36 ÷ 1.9 = 18.9 h, or 18 h 57 min.
Safe by design
This calculator does arithmetic on energy, time and cost. It stops at the point where a qualified installer has to take over. It does not size cables, fuses or breakers, it does not specify earthing or a protective device, and it does not check whether your supply can carry a charger. Those are regulated calculations in every country, and a wrong number can cause a fire or electric shock. Have all electrical work done by a qualified, certified installer who checks your supply and the local wiring rules. This page is not an installation guide.
Assumptions and limits
The tool assumes constant power from start to finish and a single flat price. Real charging is not linear: the rate falls as the battery fills, cold batteries charge more slowly, and some energy is lost as heat. Prices vary by tariff and time of day, and some tariffs have a different rate for overnight charging, so enter the price you actually pay. The tool does not include the car's battery heating, the charger's idle power or any standing charge. Battery capacity and charge level are as the car reports them, and both can drift as the battery ages. Charge levels must be between 0% and 100%, the target must be above the current level, and a blank or zero capacity or charger power returns a message instead of a result.
Using it with the rest of BuildMetricLab
Use this alongside the solar array sizing and annual yield tools to see how much of a charge your own panels could supply, and with the heat pump sizing tool when you are planning a home's electrical load. Every BuildMetricLab tool runs in your browser with no sign-up and nothing sent to a server, and the formula is shown on the page so you can check the arithmetic yourself.
Sources & methodology
Energy added is E = C × (t − s) ÷ 100, charge time is E ÷ P and cost is E × p. C is the usable battery capacity in kWh, s and t are the current and target charge in percent, P is the charger power in kW and p is your price per kWh. The time is shown in whole minutes, rounded once from the total. The tool assumes constant charger power, so the time is a best case, and it prices the energy added to the battery, not the slightly higher energy drawn from the supply. No tariff is built in. Blank, zero or negative capacity, charger power or price, charge levels outside 0% to 100%, and a target at or below the current level return a message instead of a result.
Frequently asked questions
Why is real charging slower than this?
Charging tapers as the battery fills, commonly above about 80%, and slows in cold weather or when the battery is hot. This tool assumes steady full power from start to finish, so the time it gives is a best case.
How much does a full charge cost?
Multiply the energy added by your electricity price. Set current to 0% and target to 100% to see a full-charge cost. For a 60 kWh battery at 0.27 per kWh that is 60 × 0.27 = 16.20. The figure is for the energy added to the battery, so the amount on your meter is a little higher because of charging losses.
What charger power should I enter?
Use the lower of the charger's output and the most the car can accept. A household outlet gives about 1.4–2 kW, AC wallboxes 3.7–22 kW (3–7 kW is common at home), and public DC rapid chargers 50–350 kW. A 22 kW point charging a car with a 7 kW onboard charger delivers 7 kW.
Why enter my own electricity price?
Prices vary by tariff, country and time of day and change often, so none is built in. Enter what you pay, including a cheap overnight rate if you have one. For public chargers, remember any session or idle fees are not included.
Spotted something off?
Calculations or display — let us know.













