BuildMetricLab

Planning & Budgeting

Floor Area Ratio / Plot Ratio Calculator

Floor area ratio, site coverage and what a permitted ratio lets you build

Updated October 1, 2026 · Live

What this tool does

Divides gross floor area by plot area for the floor area ratio (plot ratio, FSI or FSR), works out site coverage and storeys from the footprint, and shows the floor area a permitted ratio allows and what is left.

Floor area over plot area, footprint over plot area, and plot area times the permitted ratio, each shown on its own line.

Inputs
ft²
ft²
ft²
Result

Floor Area Ratio (FAR)

0.296

Gross Floor Area
1,600 ft²
Lot Area
5,400 ft²
Ratio as a Percentage
29.6%
Lot Coverage (footprint ÷ lot)
14.8%
Stories Implied (floor area ÷ footprint)
2.0
Floor Area Allowed at 0.50
2,700 ft²
Floor Area Left
1,100 ft²
Planning Context
The planning policy or zoning code for the district sets the limit and what counts as floor area
Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
R=GP,c=FP,A=P⋅RmaxR = \frac{G}{P},\quad c = \frac{F}{P},\quad A = P \cdot R_{max}
RR
Floor area ratio (FAR)
GG
Gross floor area (ft²)
PP
Lot area (ft²)
cc
Lot coverage
FF
Building footprint (ft²)
AA
Floor area allowed at the permitted ratio
RmaxR_{max}
Permitted ratio

How the floor area ratio calculator works

Floor area ratio is the total floor area of a building divided by the area of the plot it stands on. A 150 m² house on a 500 m² plot has a ratio of 0.30; 1,600 ft² on 5,400 ft² is 0.296, since the units cancel and only the proportion matters. The same number goes by different names. It is floor area ratio or FAR in the United States, and floor space index or FSI in Toronto and India. New South Wales and Vancouver call it floor space ratio or FSR; the UK, Hong Kong and Western Australia say plot ratio. Some codes write it as a decimal, some as a percentage, some as 0.5:1. The calculator gives the decimal and the percentage, so 0.30 and 30%, or 0.296 and 29.6%, are the same answer.

Two optional inputs add to it. The building footprint, the area of the ground floor, gives site coverage, which is the footprint divided by the plot, and the number of storeys the floor area implies. The permitted ratio from the planning policy or zoning code gives the floor area it allows on the plot and how much of that you have left. For an empty plot, enter 0 as the floor area and the allowance is the whole answer.

Floor area ratio is not site coverage

The two get mixed up because both are a percentage of the plot. Coverage is the ground the building sits on; the ratio counts every floor. A two-storey house with a 75 m² footprint on a 500 m² plot covers 15% of it but has a ratio of 0.30, because 150 m² of floor sits over 75 m² of ground. Put the same floor area on one level and coverage doubles to 30% while the ratio stays at 0.30. Codes usually limit both, and sometimes height as well, which is why a plot that has headroom under one rule can be full under another.

The London Plan 2021, in the text supporting Policy D3, asks for exactly this pair on major applications. It defines the floor area ratio as the gross external area of all floors divided by the site area, and the site coverage ratio as the gross external area of the ground floors divided by the site area. That is the calculator's model, and the two lines it reports.

What counts as floor area

The ratio is only as good as the floor area you put in, and what counts is defined by the code, not by the tape. New York's Zoning Resolution, section 12-10 defines floor area as the gross area of all floors measured to the exterior faces of the walls. It includes basements, penthouses, mezzanines and attics with eight feet of headroom. It excludes cellar space that is not lived in, attics with less than eight feet of headroom, stair and lift bulkheads, and up to 300 ft² of accessory parking for a one- or two-family house. Its own example is a 10,000 ft² lot with 20,000 ft² of floor area, a ratio of 2.0. London measures gross external area, again to the outside of the walls. New South Wales measures from the inside face of the external walls and leaves out car parking and plant rooms, so an FSR calculation needs the internal figure. Other codes net off balconies or basements, so a figure from a survey drawing may need adjusting before it goes in.

Worked examples

The default metric case is a 150 m² house with a 75 m² footprint on a 500 m² plot under a permitted ratio of 0.5. The ratio is 150 ÷ 500 = 0.30, coverage 75 ÷ 500 = 15%, and 150 ÷ 75 implies two storeys. The code allows 500 × 0.5 = 250 m² of floor area, so there is 100 m² to spare: a 100 m² extension, or a loft conversion if the roof space counts. With US units, 1,600 ft² with an 800 ft² footprint on 5,400 ft² is a ratio of 0.296 (29.6%), lot coverage 14.8%, two stories, 2,700 ft² allowed and 1,100 ft² left.

Running the other way, a buyer looking at an empty 1,200 m² site zoned at 1.5:1 enters 0 floor area and 1.5 as the permitted ratio, and can build 1,800 m². Whether that is three storeys on 600 m² or six on 300 m² is a coverage and height question, not a ratio one. And a 280 m² house on a 400 m² plot in a zone limited to 0.6 is over by 40 m², which is the figure to put to the planner.

Where the ratio is used

In the United States and Canada the ratio is a common density control in zoning codes, alongside dwellings per acre, lot coverage, height and setbacks, and a code will state the maximum for each district. In New South Wales, local environmental plans map a maximum floor space ratio for each site; other Australian states use plot ratio or floor area ratio under their own planning schemes. In England the ratio is not a national control. Councils regulate density through local plan policies, design codes and the character of the area, and plot ratio appears mainly in commercial and industrial policy, such as the 65% plot ratio the London Plan uses to assess industrial capacity. Hong Kong's building regulations use plot ratio in the same sense as this tool. Wherever you are, the limit, the measuring rules and any bonuses for affordable housing or public space are in the code for the district, and a pre-application enquiry settles how they apply to one site.

Using this with other BuildMetricLab tools

The area from coordinates calculator gives a plot's area from the corner coordinates on a survey. The architect fee calculator budgets the design work once you know what the plot can take, and the acres to hectares converter handles plot areas quoted in other units. All BuildMetricLab tools run in your browser with no sign-up, and the formula is on the page so the maths can be checked.

Sources & methodology

Floor area ratio = gross floor area ÷ plot area, shown as a decimal and as a percentage. Site coverage = ground-floor footprint ÷ plot area. Storeys implied = gross floor area ÷ footprint. Floor area allowed = plot area × permitted ratio; headroom = allowed − gross floor area. What counts as floor area is defined by the local code.

Frequently asked questions

What counts as gross floor area?

Whatever your code says it does. Most measure to the outside face of the external walls and count every floor, but they differ on basements, attics, parking, balconies and plant rooms. New York counts basements and attics with eight feet of headroom and leaves out unlived-in cellars and some parking; London uses gross external area. Check the definition for your district before you enter a figure from a drawing.

Is site coverage the same as floor area ratio?

No. Site coverage is the ground-floor footprint divided by the plot; the ratio is all floors divided by the plot. A 200 m² house over two floors on a 400 m² plot covers 25% of it and has a ratio of 0.50; spread the same floor area over one level and coverage doubles while the ratio does not move. Enter the footprint and the calculator reports both.

How much can I build on my plot?

Enter the permitted ratio from the planning policy or zoning code and the calculator multiplies it by the plot area to give the floor area allowed, then takes off the floor area you entered (enter 0 for an empty plot). Height, coverage and setback limits can stop you using all of it, and some codes add bonuses, so treat the floor area left as the starting point for a pre-application enquiry.

Does this replace professional advice?

No. It does the arithmetic on figures you enter. Which floor area counts, which ratio applies and whether a scheme is acceptable are matters for the local planning or zoning authority and an architect or planning consultant; confirm them before buying a site or designing to the limit.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.