BuildMetricLab

Kitchen

Kitchen Backsplash Calculator

Backsplash tiles, wastage and cost from run, height and tile size

Updated May 13, 2026 · Live

What this tool does

Estimates how many tiles a kitchen backsplash needs from its run, height and tile size, with a wastage allowance and the cost.

Estimates the number of tiles, and their cost, for a kitchen backsplash from its run, height, tile size and a wastage allowance.

Inputs
ft
in
in
in
%
$
Result

Backsplash Tiles Required

194

Backsplash Area
19.5 ft²
Tile Size
4.0 in × 4.0 in
Coverage per Tile
0.111 ft²
Wastage
10%
Estimated Cost
$291.00
Price it on PlainEstimate

Opens these materials as a new estimate on PlainEstimate, our free estimate and invoice app.

Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
N=⌈R⋅HtW⋅tL⋅(1+w)⌉N = \left\lceil \frac{R \cdot H}{t_W \cdot t_L} \cdot (1 + w) \right\rceil
NN
Backsplash tiles required
RR
Backsplash run
HH
Backsplash height
tWt_W
Tile width
tLt_L
Tile length
ww
Wastage allowance (decimal)

How the kitchen backsplash calculator works

A backsplash is a rectangle of wall between the counter and the upper cabinets, so the tile count is an area divided by a tile area. This calculator multiplies the run by the height to get the area, divides by the area of one tile, adds a wastage allowance and rounds up to whole tiles. The formula is N = ⌈R × H ÷ (t_W × t_L) × (1 + w)⌉. The cost is the tile count times the price per tile. The page takes the run in feet and the height and tile size in inches, and converts internally.

Example with the defaults: a 13 ft run (3.96 m) at 18 in high (457 mm) is 13 × 1.5 = 19.5 ft², or 1.81 m². A 4 × 4 in tile is 16 in², which is 0.111 ft². The tiles needed are 19.5 ÷ 0.111 = 175.5, and 10% wastage makes 193.05, which rounds up to 194 tiles. At $1.50 a tile the cost is 194 × 1.50 = $291.00.

A subway tile example: a 12 ft run at 18 in is 18 ft². A 3 × 6 in tile (76 × 152 mm) covers 18 in², which is 0.125 ft², so the wall takes 18 ÷ 0.125 = 144 tiles. With 10% wastage that is 158.4, so 159 tiles, or $238.50 at $1.50. In metric, a 4 m run at 450 mm with 100 mm tiles is 1.8 m², which is 180 tiles, or 198 with 10% wastage.

Typical US kitchen wastage

Wastage is the biggest judgement in the calculation, and the tool takes the figure you enter. For a straight lay of ordinary tile, 10% is a common allowance. Diagonal and herringbone layouts, large-format tile, and tile with a pattern or veining to match need 15% or more, because more tiles are cut and more offcuts are unusable. A kitchen with many outlets, a window and a range hood has many cuts, so it sits at the higher end. These are trade habits, not published standards.

Rounding up is an allowance of its own. In the first example 193.05 becomes 194. Tile is sold by the box, so you will probably round up again to the next box. Buy a little extra for later repairs, because a tile from a later batch may differ in shade.

What this tool does not do

It does not deduct a window, outlets or the range hood from the area, so shorten the run for an opening. It ignores grout joints, which means the count errs slightly high: with a 1/8 in (3 mm) joint, a 4 in tile covers about 6% more wall than its own area, since (4.125 ÷ 4)² = 1.063. It does not convert tiles to boxes or sheets, and it does not include grout, adhesive, trim, sealer or labour. It is a tile count and not a quote.

On-site considerations for kitchen backsplash

Measure the height between the counter and the upper cabinets at several points, because counters and walls are rarely level. The gap is commonly about 18 in (457 mm), but it varies. Plan the layout from the middle of the run or from the most visible point so that cut tiles fall at the ends, and dry-lay a few rows to check how the pattern works around outlets and the range hood. A level starting line matters more than the counter edge, which may slope.

The wall should be flat, clean and sound. Remove loose paint, and fill and sand bumps. Mosaic sheets are sold as sheets, so enter the sheet size as the tile size, for example 12 × 12 in, and the count is then sheets. Tile near a range needs a heat-tolerant adhesive and grout, so follow the product's instructions. Seal natural stone and cement-based grout where the manufacturer says to.

Codes and compliance

Tiling a backsplash does not normally need a permit. Outlets are the part with rules. Turn the power off at the breaker before working near them. A tiled wall raises the surface, so an outlet box usually needs an extender to sit flush with the finished tile, and kitchen counter outlets are normally required to have GFCI protection under the National Electrical Code in the United States. Have electrical work done by a licensed electrician. Other countries have their own rules, so follow the local ones. The TCNA Handbook and the ANSI A108 standards describe how tile is installed in the United States.

Before you order

Measure twice and sketch the wall with its openings. Choose the tile and check its nominal size, thickness and the number of tiles per box or per sheet. Convert the tile count to boxes and round up. Order all the tile from the same lot, and check each box for shade before you start. Ask the supplier about returns on unopened boxes. Compare the price per ft² or per m², not the price per box, because boxes differ in size, and add the cost of grout, adhesive and trim.

Adjusting the defaults

Every input is editable. The run, height and tile size must be above zero, and the wastage must be zero or more. A blank or zero field is refused instead of silently using a default, and a blank price hides the cost line. If tile is priced per ft² or per m², multiply the price by the tile's area to get the price per tile.

Using this kitchen backsplash calculator alongside other BuildMetricLab tools

Pair this estimate with the countertop, cabinet and range hood calculators to plan the whole kitchen. All BuildMetricLab tools run in your browser. Nothing you type is sent anywhere, and every formula is shown on the page so you can audit the maths.

Sources & methodology

Area = run × height; the page takes the run in ft and the height in inches, and converts them to m² (1 ft = 0.3048 m, 1 in = 25.4 mm). Tile area = tile width × tile length. Tiles = area ÷ tile area × (1 + wastage ÷ 100), rounded up to a whole tile. Cost = tiles × price per tile, hidden if no price is entered. The run, height and tile size must be above zero, the wastage zero or more and the price zero or more. The count uses the nominal tile size and ignores grout joints, so it errs slightly high: with a 1/8 in (3 mm) joint, a 4 in tile covers about 6% more wall than its own area, so about 6% fewer tiles are needed. The default wastage of 10% is a common trade allowance for a straight lay, not a published standard. The tool does not deduct windows, outlets or the range hood, and does not convert tiles to boxes or sheets.

Frequently asked questions

Are kitchen backsplash calculator results accurate enough to order materials?

They are a good starting count. The tile count is the area divided by the tile area, plus your wastage, rounded up. It is only as accurate as your measurements, and it ignores grout joints, which would lower the count slightly. Round up to whole boxes, because tile is sold by the box and batches can differ in shade.

What wastage percentage should I use?

For a straight lay, 10% is a common allowance. Diagonal and herringbone layouts, large-format tile and tile with a pattern to match usually call for 15% or more. These are trade habits, not published standards. Add more if you are a first-time installer or the walls are far from square.

Is this a substitute for hiring a contractor or designer?

No. It counts tiles and estimates their cost. It does not check the wall, choose an adhesive or grout, or plan around outlets and the range. For work near gas, electrical or plumbing connections, consult a licensed professional.

Can I change the unit prices?

Yes. The price per tile is editable, and a blank price hides the cost line so only the count shows. A price of zero is accepted. The run, height and tile size must be above zero, and wastage must be zero or more.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.