BuildMetricLab

Kitchen

Appliance Cut-Out Size Calculator

Aperture width and height for a built-in appliance from the body size and the side and vertical clearances on its drawing

Updated October 9, 2026 · Live

What this tool does

Works out the opening to cut for a built-in appliance from the size of the body that enters the housing and the clearance the installation drawing allows at each side and at the top and bottom. Shows the aperture in sixteenths of an inch and millimetres, with the body and clearances beside it; depth, ventilation and services come from the drawing.

Body width plus twice the side clearance, body height plus twice the vertical clearance.

Inputs
in
in
in
in
Result

Aperture Size Needed (W × H)

24 in × 33 7/8 in

Aperture Width
24 in (24.00 in, 610 mm)
Aperture Height
33 7/8 in (33.88 in, 860 mm)
Appliance Body
23 9/16 in × 33 7/8 in
Side Clearance
0.22 in (5.6 mm) each side
Vertical Clearance
0.00 in (0.0 mm) top and bottom
Depth and Services
Depth, the rear air gap and the service positions come from the installation drawing
Ventilation
Ovens and fridges need a plinth or rear air path the front aperture does not show

Diagram

610 × 872 mm
Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
Wa=w+2cs,Ha=h+2cvW_a = w + 2c_s, \quad H_a = h + 2c_v
WaW_a
Aperture width
HaH_a
Aperture height
ww
Appliance body width (in)
hh
Appliance body height (in)
csc_s
Side clearance, each side
cvc_v
Vertical clearance, top and bottom

Works out the width and height of the opening a built-in appliance needs, from the size of the body that goes into the housing and the clearance the installation drawing allows at the sides and at the top and bottom. It runs in your browser and shows the working, so every step can be checked against your own figures.

How the appliance cut-out size calculator works

The aperture is the appliance body plus twice the side clearance in width, and the body plus twice the vertical clearance in height. The two clearances are separate inputs because they are rarely the same on a real sheet. Bosch's specification for a 24 in dishwasher gives the appliance as 33 7/8 in high by 23 9/16 in wide and the required cut-out as 33 7/8 in by 24 in: 7/32 in (5.6 mm) a side and nothing top and bottom, because the feet adjust. Bosch's sheet for a 60 cm integrated dishwasher (UK) is the metric twin: the product is 815 by 598 mm and the niche 815 to 875 by 600 mm, so 1 mm a side and a height that the feet take up. Those two are the defaults. Enter the body size and the clearances from the drawing for your appliance, and the calculator returns the hole to cut.

Ovens show why the body, not the fascia, is the figure to enter. The Neff 60 by 60 cm built-in oven sheet (UK) lists the appliance as 595 by 594 by 548 mm and the niche as 585 to 595 high by 560 to 568 wide by 550 deep. The 594 mm fascia overlaps the carcase; the part that enters the housing is narrower, and the 560 mm niche is set for it. Bosch's 24 in oven installation sheet (US) makes the same point in inches: the appliance is 23 1/2 in wide overall, and the standard cut-out is 21 15/16 in (557 mm) wide by 22 15/16 to 23 1/16 in (583 to 585 mm) high. A body of 21 1/2 by 22 1/2 in with 7/32 in all round gives 21 15/16 by 22 15/16 in, which is that cut-out.

What you enter

Appliance width and height are the body that goes into the housing, from the installation drawing, not the door or the control fascia. Side clearance is the gap on each side; vertical clearance is the gap at the top and at the bottom. Both can be zero. Whirlpool's 30 in wall oven specification (US) gives a cut-out width of 28 1/2 in and a maximum recessed width of 28 1/2 in, so the side clearance there is nothing at all, and the cut-out height is a range, 26 29/32 to 29 13/32 in, against a recessed height of 26 3/4 in. Where a sheet gives a range, enter the clearance that lands on the minimum and treat the rest as adjustment.

Reading the result

The aperture rows are the width and height to cut, in sixteenths of an inch with the decimal and the millimetre figure beside them on the US side, and in millimetres with the inch figure on the metric side. Cut to the manufacturer's own installation drawing where you have it; this figure checks that the cabinet opening you are planning allows for the appliance. Heat-producing appliances also need a rear or plinth air path that the front aperture does not show, and the drawing gives the vent area as well as the hole.

Safe by design

This tool plans layout and quantities. It never sizes a gas connection or an electrical circuit. Both are regulated trades that a qualified, registered installer carries out, and in the UK that means a Gas Safe registered engineer for gas and a registered electrician for a new circuit.

Assumptions and limits

This sizes the front aperture from the clearances you enter. It does not set the depth, the rear ventilation gap, the plinth vent or the services position, all of which come from the appliance's installation manual, and it does not know whether the carcase around the opening is strong enough for a heavy oven or needs a support shelf. A rounding note for the US side: the aperture is shown to the nearest sixteenth, so 23.5625 plus two lots of 0.21875 shows as 24 in exactly, as it should, and a clearance such as 7/32 in is shown as 0.22 in rather than rounded to a sixteenth. The manual sets the final cut.

Using it with the rest of BuildMetricLab

This calculator is one step in planning the kitchen. The cabinet run planner places the housing in the run, the kitchen cabinet calculator counts the units around it, and the range hood calculator sizes the extraction above the hob. Every BuildMetricLab tool runs in your browser, with no sign-up and nothing sent to a server, and the formula is on the page so the maths can be audited.

Sources & methodology

Aperture width = appliance body width + 2 × side clearance; aperture height = appliance body height + 2 × vertical clearance. US inputs in inches are converted to mm (25.4 mm per in) before the sum and shown to the nearest sixteenth of an inch with the decimal and mm beside; clearances are shown to 0.01 in and 0.1 mm. Defaults from the sheets: Bosch SHE3AR72UC (US) appliance 33 7/8 × 23 9/16 in, cut-out 33 7/8 × 24 in; Bosch SMV4HCX40G (UK) product 815 × 598 × 550 mm, niche 815 to 875 × 600 × 550 mm. Depth, ventilation and services are not calculated.

Frequently asked questions

How much clearance should I leave?

Whatever the installation drawing says, and it differs by appliance and by axis. A Bosch 24 in dishwasher wants 7/32 in (5.6 mm) a side and nothing top and bottom; a Bosch 60 cm integrated dishwasher wants 1 mm a side in a 600 mm niche; a Whirlpool 30 in wall oven has no side clearance at all, its recessed width and the cut-out both being 28 1/2 in. Where there is no drawing yet, 5 mm (3/16 in) a side is a workable planning figure, to be replaced by the real one before anything is cut.

Does this include ventilation?

No. Ovens and fridges need a rear or plinth air gap that the front aperture does not capture, and the installation drawing gives the vent area as well as the hole. Check the maker's cut-out specification for it.

What about the aperture depth?

This sizes the front opening only. Depth, services and fixing positions come from the appliance manual. For the two defaults the sheets give a depth of 24 in for the US dishwasher and 550 mm for the UK one.

Why add clearance at all?

A little tolerance lets the appliance slide in and out, absorbs slight out-of-square cabinetry, and gives heat somewhere to go. Some makers put it all in the width and none in the height, where adjustable feet take up the difference, which is why the two clearances are separate inputs.

Spotted something off?

Calculations or display — let us know.