BuildMetricLab

Flooring

Tile & Paving Layout Planner

Plan the tile layout, see where the cuts land, and count what to order

Updated August 12, 2026 · Live

What this tool does

Lays your tile out across the area in stack bond, running bond or herringbone, then counts the full tiles, the cut tiles and the boxes to order. Shows the cut sizes and flags any sliver under a third of a tile.

180 in126 in
Cut tiles shaded · grout shown to scale

Area

in
in

Covering 157.50 ft²

Tile

in
in
in

Pattern

Courses run
Row offset

Start position

Centre positions split the leftover so the cuts land on both edges at half the width.

Cut-outs

Areas that are not tiled — a WC, an island, a hearth. Measured from the top-left corner of the area.

Ordering

%
USD
in
kg/m³
g/cm³

Price is optional. Thickness drives the grout and weight estimates — set it to 0 to leave both out of the results.

Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
tiles=clip(grid(tile+joint,phase),area);order=ceil(tilesx(1+wastage))tiles = clip(grid(tile + joint, phase), area); order = ceil(tiles x (1 + wastage))
tiletile
tile dimension along the axis (in)
jointjoint
grout joint width (in)
phasephase
grid offset set by the start position, and by the row offset in running bond
areaarea
the area rectangle being tiled (in)
wastagewastage
wastage allowance as a fraction

How the layout planner works

The planner lays the tile out across the area the way it would go down on site, then counts what it produced. It works from the module pitch, which is the tile dimension plus one joint, and clips a tiled grid to the area rectangle. Joints run between tiles and not around the perimeter, so a run of n tiles spans n × tile + (n − 1) × joint. The number of whole tiles in a run is the whole-number part of (length + joint) ÷ (tile + joint). The diagram is drawn from the same set of tiles as the counts, so the picture and the numbers cannot disagree.

Take a 180 × 126 in room (4,572 × 3,200 mm) with 24 × 12 in tiles (610 × 305 mm), a 1/8 in joint, stack bond and 10% wastage. Across the width, 7 whole tiles span 168.75 in, which leaves an 11.13 in cut tile at the far wall. Along the length, 10 whole rows span 121.125 in, which leaves a 4.75 in cut row. That is 8 × 11 = 88 tiles, 70 whole and 18 cut. Adding 10% gives 96.8, which rounds up to 97.

The tool counts the tiles a layout needs. Most calculators divide the area by one tile and add a percentage, which gives a rough purchase quantity but nothing about where the cuts fall. The tile calculator on this site does that quickly. Use this planner when the cuts matter.

Why the start position matters

Starting in a corner sends all of the leftover to the two far edges, giving one cut band along each. A centre start keeps the same whole tiles and splits the leftover between both sides, so each cut is about half as wide, and you gain a second band of cuts on each axis. The tile count rises and the cuts get thinner. That is the opposite of what many people expect, so it is worth seeing in numbers.

In the same room, switching to a centre start gives 9 × 12 = 108 tiles (70 whole, 38 cut), and 119 with 10% wastage. The edge cuts become 5.5 in across the width and 2.31 in along the length. Both are below a third of the tile (8 in and 4 in), so the planner flags both. The corner start for this room has no sliver, so it is the better choice here. The comparison table on the page scores all nine start positions for the same inputs, which is the quickest way to see this. A centre start helps when you want matching cuts on opposite walls, for example around a doorway or a feature in the middle of the floor. It does not widen cuts.

A concrete case where the corner start does fail is a 98 in wide wall with 24 in tiles and a 1/8 in joint. Four whole tiles and their three joints take 96.375 in, so the last cut is 1.5 in wide. Setting the same wall out by hand with 3 whole tiles in the middle and a cut at each end gives (98 − 3 × 24 − 4 × 0.125) ÷ 2 = 12.75 in each, which is far easier to cut and bed. The planner does not offer this balanced layout, so work it out with the formula and check the result against the tile maker's guidance.

Reading the cut list

For stack and running bond the planner groups every cut tile by its finished size and gives a count of each. Sizes are shown in inches to two decimal places; the planner also keeps the millimetre values behind them. A running bond produces two different sets of end cuts, because the shifted rows start and finish at different points from the unshifted ones, so the leading and trailing cuts are worked out separately and not assumed to mirror each other.

For a running bond with a 50% offset, the same room in 24 × 12 in tile needs 65 whole and 23 cut tiles, 97 with wastage. The main cuts are 24 × 4.75 in (7 pieces), 23.19 × 12 in (5) and 11.94 × 12 in (5), so alternate rows have different end cuts.

Herringbone is laid at 45° to the walls, so almost every tile along the edge is a different shape. The planner reports the number of whole and cut tiles but no size-by-size schedule. The pattern is built on a tile twice as long as it is wide, which is the classic herringbone ratio. At any other ratio the motif does not close exactly, so the count is an approximation, and the page says so when your tile is not 2:1.

Slivers

Any cut narrower than a third of the tile in that direction is flagged with the edge it affects. A thin strip is hard to cut without cracking, hard to bed flat and obvious against the wall. The one-third limit is a working threshold chosen for this tool and is not a figure from a standard, so treat it as a prompt to look at the layout.

Nothing is corrected for you. Within this tool, a sliver on a corner start does not go away by choosing another start, because every start keeps the same whole tiles and the cut can only stay the same width or halve. What changes it is the joint width (within the range the tile maker allows), the tile size, the course direction, or setting out by hand with one fewer whole tile in the run so that the leftover is shared between two wider cuts. The diagram and the comparison table update as soon as you change an input, so you can test each option.

What this tool does not do

It counts tiles, cuts, boxes and an indicative grout quantity, and it estimates tile weight. It does not specify adhesive or trowel size, assess the substrate, place movement joints, or judge whether a tile or layout suits the room. Those decisions depend on the build-up, the exposure and the product, and they belong with the manufacturer's instructions and a qualified tiler. Movement joints, substrate preparation and setting materials are covered by the TCNA Handbook in the United States and by Tile Association guidance in the United Kingdom. Check the standard that applies where you work.

The grout figure uses the joint volume per square metre, (tile length + tile width) ÷ (tile length × tile width) × joint width × tile thickness × grout density. It is an estimate. Real coverage changes with the product, how fully the joints are packed, square or cushioned edges and mixing loss, so use the manufacturer's coverage table when you buy. Cutting ceramic and porcelain releases respirable crystalline silica dust, so cut wet or with dust extraction and wear a suitable respirator. The HSE page on silica in construction, listed in the references, explains the hazard.

Adjusting the defaults

Every figure is editable. Wastage starts at 10%, which suits a simple rectangular room. Raise it where the area is cut about with hips, alcoves or a lot of edge work, and for patterns with many cuts. Tiles per box starts at 1, so the box count matches the tile count until you enter a real pack size. If a box holds 10 tiles, 97 tiles is 10 boxes (100 tiles). Box sizes are on the product label, so enter the real number to get a box count. Price per box is optional, and a blank price leaves the cost out.

Tile thickness, tile density and grout density drive the weight and grout estimates. Set the thickness to 0 to leave both out. For the 180 × 126 in example with 3/8 in thick tile, the estimate is about 7.7 lb (3.5 kg) of dry powder. The 97 tiles to order weigh roughly 395 kg (870 lb) at a density of 2,300 kg/m³. Use the unit switch to enter millimetres or inches, and the values already on screen are converted when you switch. Dimensions are the wall-to-wall size of the area to tile and the face size of one tile excluding the joint.

Sources & methodology

Tiles are placed by clipping a phased grid to the area rectangle, with a module pitch of tile dimension plus one joint and joints counted between tiles only. Start position sets the grid phase; a centre start keeps the whole tiles and splits the leftover between both edges. Running bond shifts alternate rows by the chosen fraction of a module and lays each row out independently. Herringbone is generated on a two-tile lattice rotated 45° to the area and clipped, and is exact only for a 2:1 tile. Orders are the tile count × (1 + wastage), rounded up, then divided into whole boxes. Grout kg = (L + W) ÷ (L × W) × joint × thickness × density × area; tile weight = tiles × volume × density. A blank, negative or fractional value where a whole number is needed is refused.

Frequently asked questions

Why does the start position change how many tiles I need?

Starting in a corner pushes the whole leftover to the two far edges, so you get one band of cuts along each axis at the full leftover width. A centre start keeps the same whole tiles and splits the leftover in half, which puts a cut band on both edges, each roughly half as wide. The tile count therefore usually rises, and the cuts are narrower, so they are more likely to be slivers, not less. On a room that nearly divides exactly, a corner start can leave a sliver only a few inches wide.

What counts as a sliver, and why doesn't the tool fix it?

This planner flags any cut narrower than a third of the tile in that direction. The one-third limit is a working threshold, not a standard. Thin strips crack while you cut them, they are awkward to bed evenly, and they draw the eye along the wall they sit against. The tool does not move your layout automatically because the fix is a judgement call. Changing the joint within the tile maker's range, the tile size or the course direction can help, as can setting out by hand with one fewer whole tile so the leftover is shared between two wider cuts.

Does grout go around the outside edge of the tiling?

Not in this calculation. Joints are counted between tiles only, so a run of tiles spans the tile widths plus one fewer joint than there are tiles. Perimeter gaps against walls are expansion or accommodation gaps, not grout joints, and they vary with the substrate and the covering, so they are left out of the geometry here. If your layout depends on a specific perimeter gap, subtract it from the area dimensions before entering them.

Why is there no cut list for herringbone?

A herringbone laid at 45° meets every wall at an angle, so almost every perimeter tile is a different irregular shape. Listing them would produce a schedule as long as the perimeter itself, which is no use at a tile saw. The planner reports the number of whole and cut tiles for your tile size and area, and the diagram shows where the cuts fall. The pattern assumes a tile twice as long as it is wide, the classic ratio. At other ratios the count is approximate.

How accurate is the grout estimate?

Treat it as a starting figure. It comes from the joint volume implied by your tile size, joint width and tile thickness, multiplied by a powder density you can adjust. Real coverage moves with the product, how fully the joints are packed, whether the tile edges are cushioned or square, and how much you lose mixing. Manufacturers publish coverage tables for their own products, and those are better than any generic formula, including this one.

Spotted something off?

Calculations or display — let us know.