Driveway & Hard Paving
Asphalt Calculator
Estimates short tons of hot-mix asphalt for a driveway or parking lot
Updated May 28, 2026 · Live
What this tool does
Estimates the short tons of hot-mix asphalt (HMA) needed to pave a driveway or parking lot at a specified compacted depth and density.
Estimates the short tons of hot-mix asphalt needed to pave a driveway or parking lot at a specified compacted depth and density.
People also use
Formula Used
Formula Used
How the asphalt calculator works
Asphalt is ordered by weight, so the calculator turns an area and a thickness into a volume and then into a mass. Volume is area × compacted depth, and tonnage is volume × the compacted density of the mix: T = A × d × ρ. It then multiplies the tonnage by your price per ton or tonne. It runs in your browser and shows its working.
The default is a 400 ft² (37 m²) driveway laid 2 in (51 mm) thick at 148 lb/ft³ (2.37 t/m³). That is 400 × 2/12 = 66.7 ft³ (2.47 yd³), which weighs 66.7 × 148 = 9,867 lb, or 4.93 US short tons. At $130 per ton the cost is $641.33. In metric, 40 m² at 50 mm and 2.4 t/m³ is 2.00 m³, or 4.80 tonnes, and at 95 per tonne it costs 456.00.
A handy check is the weight per unit of area. Hot-mix asphalt weighs about 110 lb per square yard for each inch of thickness (148 lb/ft³ × 9 ft² ÷ 12 gives 111), or 2.4 kg per square metre for each millimetre at 2.4 t/m³. A 50 mm layer therefore carries about 120 kg/m². Tonnage scales directly with depth, so 3 in over the same 400 ft² is 1.5 times the 2 in figure: 7.40 tons and $962.00.
Typical asphalt depths and densities
The depth you enter is the compacted thickness of the asphalt itself, after rolling. It is not the full pavement build-up, which also contains a compacted stone base. Residential driveways in the US commonly use a 2 to 3 in (50 to 75 mm) lift of hot-mix asphalt over a compacted aggregate base. Car parks and roads use thicker sections built from a binder course and a surface course. The stone size in the mix sets a lower limit, because a lift is normally laid at least two to three times the nominal maximum aggregate size.
Dense-graded mixes compact to about 2.30 to 2.45 t/m³ (144 to 153 lb/ft³), and open-graded mixes sit lower. The default of 148 lb/ft³ is 2.37 t/m³. Only your supplier knows the figure for the mix they deliver, so ask. Note the unit change between regions: a US short ton is 2,000 lb (907 kg), while a tonne is 1,000 kg (2,205 lb). A price of $130 per short ton is $143.30 per tonne, so check which one a quote uses.
What this tool does not do
It does not size the stone base underneath, price edge restraints, or add an allowance for waste. A rough, uneven base uses more asphalt than a flat one, and many contractors order a few per cent extra for that and for edges. For the default, 5% extra is 5.18 tons. It does not check that the thickness is enough for the traffic it will carry, which depends on the base and the ground. It is not a quote, and it does not confirm that the work complies with the rules where you live.
Permits and stormwater
Rules vary a great deal by place. In the US, a driveway that joins a public street usually needs a permit from the local public works department, and many municipalities limit the area of impermeable surface or require stormwater to be captured on site. In England, laying more than 5 m² of impermeable paving in a front garden needs planning permission unless the rainwater drains to a lawn or border, or the surface is permeable, as set out in GOV.UK guidance on permeable surfacing of front gardens. Other countries and regions have their own rules, so ask the local authority before you start.
Code and compliance
Water running off a driveway should not flow uncontrolled onto a public road or a neighbour's land in most places, and slope, setback and edge details are set locally. Mix specifications are national or regional standards: in the US, the Superpave mix design method is published as AASHTO M 323, and the Federal Highway Administration gives an overview of asphalt pavements and materials. Other regions, such as Europe and the UK, use their own mix standards. Ask your supplier which one their mix meets.
Before you order
Compare the calculator's total with a supplier quote, and confirm what the quote includes. Ask which mix it is (the stone size, such as a 9.5 mm surface course, and the binder grade), what compacted density they assume, whether the price is per short ton or per tonne, and whether delivery and laying are included. Hot asphalt must be laid and rolled while it is still hot, so also confirm the delivery window and make sure the base is ready before the lorry arrives.
Adjusting the defaults
Every input can be changed. Enter your own area, depth, density and price per ton or tonne, and the result recalculates as you type. The default price is a placeholder, not a market rate, and prices move with oil and aggregate costs, so use a current quote. Leave the price blank if you only want the tonnage.
Using this asphalt calculator alongside other BuildMetricLab tools
The block paver, resin bound and stepping stone calculators in the same category cover other driveway and path surfaces if you are comparing options. Every BuildMetricLab tool runs in your browser with no sign-up and nothing sent to a server, and each one shows its formula so you can check the maths.
Sources & methodology
Volume = area × compacted depth; mass = volume × compacted density. US: short tons = (area in ft² × depth in ft × density in lb/ft³) ÷ 2,000. Metric: tonnes = area (m²) × depth (m) × density (t/m³). A 148 lb/ft³ density equals 2.37 t/m³, which is about 110 lb per yd² per inch of thickness. Estimated cost = mass × price per ton or tonne. The depth is the compacted thickness of the asphalt layer only. The base, edging, waste allowance and delivery are not modelled. Every result is calculated from the values you enter, all inputs are editable, and no time-sensitive prices or rates are embedded.
- AASHTO M323 — Standard Specification for Superpave Volumetric Mix Design
- National Asphalt Pavement Association (NAPA) — Asphalt Pavement Resources
- ASTM D6927 — Standard Test Method for Marshall Stability and Flow of Asphalt Mixtures
- US FHWA: Asphalt pavements and materials
- GOV.UK (England): Permeable surfacing of front gardens
Frequently asked questions
Are asphalt calculator results accurate enough to order materials?
Use them as a starting estimate. The tonnage is exact for the area, depth and density you enter, but the real figure depends on how even the base is, the edges and the mix delivered. Many contractors order a few per cent extra for that. Check the final quantity with your supplier before ordering.
What compacted density should I use?
Dense-graded hot-mix asphalt typically compacts to about 144-153 lb/ft³ (2.30-2.45 t/m³). The calculator defaults to 148 lb/ft³ (2.37 t/m³), a common figure for dense-graded mixes. Your supplier can confirm the figure for the mix you order, and entering that value gives the closest estimate.
Does this replace professional advice?
No. This tool is a planning estimate. For work that affects structure, drainage to a public sewer, or compliance with local rules, consult a qualified contractor or design professional.
Can I change the unit prices?
Yes. Enter your own price from a recent quote. On the US version the price is per short ton (2,000 lb); on the metric version it is per tonne (1,000 kg). $130 per short ton is $143.30 per tonne, so check which unit your quote uses.
Spotted something off?
Calculations or display — let us know.
Related tools
Calculators from other categories that planners often reach for next.













