BuildMetricLab

Concrete & Foundations

Concrete Wall Calculator

Calculates concrete volume for poured walls, foundation walls, and stem walls

Updated May 13, 2026 · Live

What this tool does

Estimates the concrete volume for a poured wall, foundation wall or stem wall, with formwork area, weight and cost.

Estimates cubic yards of concrete required for a poured, foundation, or stem wall based on length, height, and thickness.

Inputs
ft
ft
in
%
$
Result

Concrete Wall Volume

4.15 yd³

Face Area
160.0 ft²
Net Volume (no wastage)
3.95 yd³
Formwork Area (both sides)
320.0 ft²
Estimated Weight (at 150 lb/ft³)
8.39 tons
Estimated Cost
$746.67
Price it on PlainEstimate

Opens these materials as a new estimate on PlainEstimate, our free estimate and invoice app.

Plain Estimate
From BrightScale Labs
Invoice maker
Quote at the door. Signed on the spot.
Estimates and invoices for trades, built while you are still in the room.
Scan to get
Get it onGoogle Play

People also use

Formula Used
V=L×H×t×(1+w)V = L \times H \times t \times (1 + w)
VV
Concrete volume
LL
Wall length
HH
Wall height
tt
Wall thickness
ww
Wastage allowance (decimal)

How the concrete wall calculator works

The calculator treats a poured wall as a solid box. It multiplies the wall length, height and thickness to get the volume of concrete in place, then adds your wastage allowance to give the amount to order. It also returns the face area, the formwork area for both sides, the weight and, if you enter a price, the cost. Every figure is an estimate.

The formula is V = L × H × t × (1 + w). In metric, L and H are in metres and t is in millimetres divided by 1,000. In US units, L and H are in feet, t is in inches divided by 12, and the cubic feet are divided by 27 to give cubic yards.

Typical concrete wastage

The default allowance is 5%. That suits a wall poured into tight, plumb forms on a level base. Raise it to 7–10% when the wall is cast against rough ground, when tall forms may bulge under pressure, or when the crew is new to the work. The last truck is rarely full, so many builders also order a small margin rather than risk a cold joint.

Worked example, US units: a wall 20 ft long, 8 ft high and 8 in thick holds 20 × 8 × (8 ÷ 12) = 106.7 ft³, which is 3.95 yd³. At 5% wastage you order 4.15 yd³. At $180 per yd³ that is about $747. Worked example, metric: 5 m × 2.4 m × 0.2 m = 2.40 m³, or 2.52 m³ at 5%. At 135 per m³ the cost is 340.20.

What this tool does not do

It does not replace a professional quote, adjust for regional prices, assess structural adequacy or confirm that the wall meets building rules. It makes no deduction for door or window openings and it does not add the footing, so calculate the footing separately. If your wall has a large opening, subtract that volume yourself.

On-site considerations for concrete walls

Fresh concrete presses on the forms like a liquid, and the pressure grows with the height of the pour. A common planning figure is about 150 lb/ft² for every foot of depth (roughly 24 kN/m² per metre), so tall walls are poured in lifts and the forms are braced and tied. ACI 347 covers formwork design. Place and vibrate the concrete soon after it arrives, because the workable time is limited and shortens in hot weather.

The tool shows a weight too. The 5 m wall above weighs about 2.52 × 2,400 = 6,048 kg (13,330 lb), which matters for lifting, transport and the load on the footing.

Thickness has a large effect on the result. Because volume scales directly with it, a 12 in (300 mm) wall needs 50% more concrete than an 8 in (200 mm) wall of the same size. Check the thickness against the form width and the drawing before you rely on the total, and measure the height from the top of the footing, not from ground level.

After the pour, keep the wall damp or covered so it cures slowly. Early drying cracks the surface and weakens it, and the forms should stay on until the concrete has gained enough strength for the design to allow stripping.

Codes and compliance

Residential foundation walls in the United States are covered by the International Residential Code, and structural concrete design follows ACI 318. In England, Approved Document A covers structure, and other countries have their own codes. Frost depth and soil capacity are local. Walls that carry load or retain soil should be designed by a qualified engineer, and many places require a permit or inspection before the pour.

Before you order

Specify the ready-mix by strength (psi or MPa), slump and maximum aggregate size, and say how the concrete will be placed: by chute, barrow or pump. Check the delivered price per cubic yard or cubic metre, any short-load charge and the minimum order. For small walls, bagged mix is an option. An 80 lb bag yields about 0.6 ft³ (0.017 m³), so the 4.15 yd³ example needs about 187 bags, which is why a delivered load is usually the better choice.

Adjusting the defaults

Every input is editable. Enter your own dimensions, wastage and price, and the output recalculates at once. The defaults are plausible starting points only, so your own numbers always override them. Switch between metric and US units at any time and the values convert.

Using this concrete wall calculator alongside other BuildMetricLab tools

Use the wall volume with the footing, slab and column calculators to build up the full concrete quantity for a structure. All BuildMetricLab tools run in your browser, so nothing you type is sent anywhere, and every formula is shown on the page so you can check the maths.

Sources & methodology

The tool treats the wall as a solid rectangular prism. Volume = length × height × thickness, then multiplied by (1 + wastage ÷ 100). In US units, length and height are in feet and thickness in inches, so V (yd³) = L(ft) × H(ft) × t(in) ÷ 12 ÷ 27. Formwork area is 2 × length × height, counting both faces, and weight uses 150 lb/ft³ (2,400 kg/m³) for normal-weight concrete. Openings, steel and footings are not deducted or added. The 5% default is a planning allowance from common trade practice, not a figure set by a standard; replace it with your own.

Frequently asked questions

Are concrete wall calculator results accurate enough to order materials?

They are accurate for the geometry you enter, but treat them as an estimate. The tool multiplies length, height and thickness and adds your wastage allowance. Out-of-plumb forms, an uneven base, spillage and the last part-load all change the true figure, so confirm the quantity with your ready-mix supplier before you order.

What wastage percentage should I use?

The default is 5%, a common allowance for a simple, accurate formwork wall. Use 7–10% for a wall poured against rough excavation, tall forms that may bulge, or a first pour. For example, a wall of 3.95 yd³ (3.02 m³) needs 4.15 yd³ (3.17 m³) at 5% but 4.34 yd³ (3.32 m³) at 10%.

Does this replace professional advice?

No. This is a planning estimator. Walls that carry load, retain soil or sit on a foundation fall under building codes, and thickness, reinforcement and the pour method need a licensed designer or engineer. Check gas, electrical and drainage work with the relevant qualified professional too.

Can I change the unit prices?

Yes. Every field is editable, including the price. Enter the delivered price per cubic yard (or per cubic metre in metric) from your supplier's quote. Leave the price blank and the tool drops the cost row.

Spotted something off?

Calculations or display — let us know.

Calculators from other categories that planners often reach for next.